background image

2

Do not allow the hair or the skin of the customer to 
contact the heater guard. 

Do not step on or lean over the main unit or the stand.

The stand is provided with casters.
Falling of the equipment may result in
an electric shock, fire, or damage.

WARNING

Warning concerning Power Supply.

Be sure to turn off the power to the main unit 
each time the work is completed.
Be sure to disconnect the power plug before 
moving the product.

Do not insert a metal object, such as a pin or 
the like, into the ring to remove dust accumulated 
in the slit, etc., when fixing the roller ball. Neglecting 
this warning may result in an electrical shock or 
ignition caused by an electrical short circuit.

IMPORTANT SAFETY INSTRUCTIONS

An appliance should never be left unattended 
when plugged in.

Be careful to avoid allowing the hair or the skin of 
the customer to contact the heater guard while the 
customer dozes during operation or after using the 
roller ball. Neglecting this warning may result in a 
burn injury.

If the blades or the area near the blades of the 
power plug are contaminated with waste hair or 
chemical agent, wipe the area thoroughly with a 
dry cloth.

Disconnect the power plug before fixing up the equipment. 

Be sure to disconnect the power plug when fixing 
the equipment. Do not do this with wet hands. 
Neglecting this warning may result in an electrical 
shock or injuries.

Shocks to the equipment in operation.

Do not expose the equipment to shocks or
impacts during operation. Neglecting
this warning may result in falling of
the equipment, thus causing electric shock,
fire, breakage, or injuries.

Do not operate the equipment in a tilted state. 

Incorrect detection by the infrared temperature 
sensor may cause abnormal heating of the customer 
head. In addition, falling of the equipment may  result 
in electric shock, fire, or damage.

Never drop or insert any object into any opening.

READ ALL INSTRUCTIONS BEFORE USING. KEEP AWAY FROM WATER. 

Do not allow the hair or the skin of the customer to 
contact the heater guard. 

Do not step on or lean over the main unit or the stand.

The stand is provided with casters.
Falling of the equipment may result in
an electric shock, fire, or damage.

DANGER

Warning concerning Power Supply.

Do not water the equipment. 

Be sure to turn off the power to the main unit 
each time the work is completed.
Be sure to disconnect the power plug before 
moving the product.

Do not insert a metal object, such as a pin or 
the like, into the ring to remove dust accumulated 
in the slit, etc., when fixing the roller ball. Neglecting 
this warning may result in an electrical shock or 
ignition caused by an electrical short circuit.

Be careful to avoid allowing the hair or the skin of 
the customer to contact the heater guard while the 
customer dozes during operation or after using the 
roller ball. Neglecting this warning may result in a 
burn injury.

If the blades or the area near the blades of the 
power plug are contaminated with waste hair or 
chemical agent, wipe the area thoroughly with a 
dry cloth.

Disconnect the power plug before fixing up the equipment. 

Be sure to disconnect the power plug when fixing 
the equipment. Do not do this with wet hands. 
Neglecting this warning may result in an electrical 
shock or injuries.

Shocks to the equipment in operation.

Do not expose the equipment to shocks or
impacts during operation. Neglecting
this warning may result in falling of
the equipment, thus causing electric shock,
fire, breakage, or injuries.

Do not operate the equipment in a tilted state. 

Incorrect detection by the infrared temperature 
sensor may cause abnormal heating of the customer 
head. In addition, falling of the equipment may  result 
in electric shock, fire, or damage.

Do not insert a metal object into the ring. 

Always unplug this appliance immediately after
using.

Do not place or store appliance where it can fall
or be pulled into a tub or sink. Do not use while 
bathing. Do not place in or drop into water or 
other liquid. Do not reach for an appliance that 
has fallen into water. Unplug immediately.

To reduce the risk of burns, electroction, fire, or injury to persons:

OW!

Summary of Contents for AK-S23S

























Reviews: