background image

 

 

Up: 

Means up elevator. Direction in which the 

trailing edge of the elevator is pointing up.

 
 

Waring:

 Note: This equipment has been tested and found to comply with the limits for a Class B digital device,

 pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against

 harmful interference in a residential installation. This equipment generates uses and can radiate radio 

frequency energy and, if not installed and used in accordance with the instructions, may cause harmful 

interference to radio communications. However, there is no guarantee that interference will not occur in 

a particular installation. If this equipment does cause harmful interference to radio or television reception,

 which can be determined by turning the equipment off and on, the user is encouraged to try to correct 

the interference by one or more of the following measures:  

 Reorient or relocate the receiving antenna.

 Increase the separation between the equipment and receiver.  

 Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.  

 Consult the dealer or an experienced radio/TV technician for help.

 

 This equipment complies with FCC radiation exposure limits set forth for uncontrolled environment .

This equipment should be installed and operated with minimum distance 20cm between the radiator

& your body.  This transmitter must not be co-located or operating in conjunction with any other

 antenna or transmitter.

 

Any Changes or modifications not expressly approved by the party responsible for compliance could 

void the user's authority to operate the equipment.

 

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 
(1) This device may not cause harmful interference, and (2) This device must accept any interference 
received, including interference that may cause undesired operation.

 

Summary of Contents for AT402








Reviews: