background image

15

Operation - Remote Controller

Plug the power cable into the electrical outlet. 

The system will turn ON - the RED status LED will turn off.

 

The YELLOW (Line In) status LED will light up and the BLUE (Bluetooth) status LED 

will be flashing.

 

 

Turn the system ON and OFF

 

Turn OFF the system by pressing Power OFF button -the RED status LED will light up. 

 

Turn ON the system by pressing Power ON button - the RED status LED will turn off.

 

The YELLOW (Line In) status LED will light up and the BLUE (Bluetooth) status LED 

will be flashing.

 

 

Note! 

When the system is in the standby mode then all LEDs are off - after a signal is 

detected on the LINE input or the Power ON button is pressed, the system will switch 

from the standby mode to the Power ON mode - The YELLOW (Line In) status LED will 

light up.

Bluetooth

®

 Priority and Select the Input 

 

Press the Bluetooth BT Priority ON button to enable the auto-switching feature – the 

Bluetooth input will be automatically selected when a Bluetooth device is paired. 

Press the Bluetooth BT Priority OFF button to deactivate this feature – then the input 

has to be selected manually.

When the Bluetooth BT Priority is ON, press the BT button and the 

Bluetooth

®

 will be 

paired in a few seconds and the 

Bluetooth

®

 input will be selected.

Press the LINE button to select this input - If the LINE is selected make sure the audio 

source is properly connected to the rear panel LINE IN input of the master speaker - 

turn on your audio source and start playback. The YELLOW (LINE IN) status LED will 

light up. 

If the YELLOW (LINE IN) status LED is not light – it means that the 

Bluetooth

®

 input is 

selected. 

For the 

Bluetooth

®

 operation and pairing – check “

Bluetooth

®

 Connection” for more 

details. 

 

Note! 

In the Bluetooth BT Priority mode and when a Bluetooth device is not paired, the 

BT button will not operate and the LINE input will be selected automatically. 

 

Volume Regulation

 

You can adjust the volume level down ▼ and up ▲ by pressing the Volume buttons.

 

Note! 

Distortions and sound quality worsening may occur when the volume level is too 

high – when you can hear that then immediately lower the volume level otherwise it  

may damage the system - this may void your warranty.

Tone Regulations

 

Bass

 

You can adjust the bass level.

Press Bass - button to decrease the amount of low frequencies by -1dB.  

Press Bass + button to increase the amount of low frequencies by +1dB.   

Summary of Contents for RB-1650BT





















Reviews: