Taco VT Series Installation And Operation Instructions Manual Download Page 11

Page: 11 / 12

H6: PACKING BOX

TROUBLE SOURCE

PROBABLE CAUSE

REMEDY

Excessive leakage

1. Improper packing

2. Incorrect type or defective packing

3. Worn shaft or sleeve

1. Repack correctly.

2. Repack with the correct grade for service.

3. Remachine or replace scored parts.

Packing box overheated

1. Improper packing procedure

2. Packing too tight

3. Insufficient lubrication

4. Incorrect type of packing

1. Repack correctly.

2. Repack with the correct grade for service.

3. Remachine or replace scored parts.

Packing wears prematurely

1. Improper packing

2. Insufficient lubrication

3. Shaft or sleeve scored

4. Incorrect type of packing

1. Remove cause.

2. Replace worn parts.

3. Remachine or replace

I: ORDERING PARTS

Please contact your TACO representative with the serial

number of the pump for more information. The serial number of

the pump can be found on the pump information tag.

NOTES

Summary of Contents for VT Series













Search results

Summary of Contents for VT Series

Reviews:

Related manuals for VT Series

Brands by name

Popular brands

Taco VT Series, Installation And Operation Instructions Manual

Search results

Summary of Contents for VT Series

Reviews:

Related manuals for VT Series

Brands by name

Popular brands