18
aDDiTiOnaL safETY rULEs fOr MiTrE saW
1. this saw is recommended for cutting wood, non-ferrous metal and plastic only.
2. never use a saw blade which is not recommend in this owner’s manual.
3. do not use saw blades with High speed steel
(HSS) or damaged or deformed.
4. do not use the saw without the guards in position, in good working order and properly maintained.
5. Replace the table insert when worn.
6. use only saw blades recommended by the manufacturer and which conforms to En847-1.
7. connect your mitre saw to a dust collecting device= (I. d.Ø32mm) when sawing.
8. Select saw blades in relation to the material to be cut.
9. check the maximum depth of cut.
10. when sawing long work pieces, always use extra support to provide better support, and use clamps or other clamping devices.
11. wear suitable personal protective equipment when
necessary, this could include:
- hearing protection to reduce the risk of induced hearing loss;
- eye protection;
- respiratory protection to reduce the risk of inhalation of harmful dust;
- gloves for handling saw blades (saw blades shall be carried in a holder wherever practicable) and rough material.
12. the operator is adequately trained in the use adjustment and operation and operation of the machine.
13. Provide for adequate room lighting at your workplace or for adequate lighting of the immediate work area.
14. When fitted with laser no exchange with different type of laser is permitted. Repairs shall only be carried out by the laser manfacturer or an
authorized agent.
15. Refrain from removing any cut-offs or other parts of the workpiece from the cutting area whilst the machine is running and the saw head is not
the rest position.
16. never stand on this tool. Serious injuries could occur when this tool tips over or when coming in contact with the saw blade.
17. Never use the mitre saw near flammable liquids, vapors, or gases.
18. Remove all nails that may be in the workpiece to prevent sparking that could cause a fire.
19. T o avoid fire or toxic reaction, never use gasoline, naphtha acetone, lacquer thinner or similar highly volatile solvents to clean the mitre
saw.
20. Keep the saw with proper footing on a table to decrease noise and vibration.
21. Always use the designated the sides of saw base for transportation
WarninG!
• Ensure that the arm is securely fixed when bevelling.
• Keep the floor area around the machine level, well maintained and free of loose materials e.g. chips and cut-offs.
• Use correctly sharpened saw blades. Observe the maximum speed marked on the saw blade.
• When fitted with laser, no exchange with different type of laser is permitted. Repairs shall only be carried out by the laser
manufacturer or an authorised agent.
• Refrain from removing any cut-offs or other parts of the workpiece from the cutting area whilst the machine is running and
the saw head is not in the rest position.
• Ensure that the machine is always fixed to a bench, whenever possible
sPECifiaCTiOns
Input power:
1400w
no load speed:
5500min-1
Blade size:
Ø210mm x Ø30mm bore
number of teeth:
40
Mitre table angles:
0° to 45° to the left & right
Bevel cuts:
0° to 45° to the left
Straight cut at
0° x 0°: 55 x 120 mm
Mitre cut at 45° x 0°:
55 x 83 mm
Bevel cut at 0° x 45°:
30 x 120 mm
compound mitre cut
at 45° x 45°:
30 x 83 mm
Insulation class:
double insulated
aCCEssOriEs
the tS210l compound Mitre Saw is supplied with the
following accessories as standard:
• Dust bag
• Hex key
Summary of Contents for TS210L
Page 2: ......
Page 7: ...illustrations 7 ...
Page 8: ...8 ...
Page 32: ...VUE éclatée exploded view 32 ...
