39
Problem:
If the SADV 1250 R HD is connected to
a TV set directly using a SCART lead,
this can result in a scrolling DVD
picture appearing on all programme
memories. This problem may occur
with many types of TV.
Cause:
The TV set is analysing the A/V switching
signal from the DVD player incorrectly, or
not at all.
Remedy 1:
If possible, call up the Setup menu for
your TV set and switch off RGB priority.
Select the RGB signal type for the DVD
SCART input of your TV set.
Remedy 2:
If your television does not provide this
option, connect the DVD player using an
S-VHS lead, or use a SCART lead without
RGB signal. Ask your
dealer for help
with this.
Remedy 3:
When watching TV, switch off the DVD
player by pressing the
button on
the front panel.
Problem:
When used in a non-
system the
machine does not respond to remote
control commands, or cannot be
switched on by remote control.
Cause:
E 2000
remote control receiver not con-
nected.
Remedy:
Connect the
E 2000
remote control
receiver as shown in
Wiring Diagram 3
.
Press the
source select button
(or
) on the remote control handset
to switch the machine on.
Problem:
When operating the menu for the surround
decoder
or
surround
receiver,
the
SADV 1250 R HD
also responds.
Cause:
E 2000
connected
to
the
SADV 1250 R HD
.
Remedy:
Connect the
E 2000
to the pre-amplifier,
integrated amplifier or receiver.
Problem:
MP3 CD does not play back.
Cause:
MP3 format not supported
(see
'
Playing
MP3 CDs
'
).
Remedy:
(see
'
Playing
MP3 CDs
'
)
Problem:
Distorted or double picture at the YUV
output
Cause:
P-Scan switched on buit TV set not
compatible with progressive video signals
Remedy:
Switch P-Scan off (
button on the
front panel).
Problem:
No picture.
Cause:
Video-output switched off
Remedy:
switch ON the video output (
button on the front panel)
Problem:
Bad or distorted sound reproduction
Cause 1:
Multi channel mode is selected but only a
stereo amplifier is connected
Remedy:
Switch to STEREO operation (
-
button on the front panel).
Cause 2:
a multi channel amplifier is used but it is
switched to STEREO operation mode
Remedy:
switch the surround-amplifier to multi
channel mode
Problem:
'
overheat
overheat
overheat
overheat
'
displayed, playback stopped
Cause:
Device is over heated, too little flow of
cooling air
Remedy:
change the installation of your system to
provide sufficient cooling.
do not place the
SADV 1250 R HD
on top
of hot equipment like amplifiers or
surround receivers
Problem:
Not possible to switch to MCH mode
Cause:
Disc does not contain a multi channel
layer
Remedy:
no remedy, disc can only be played back
in Stereo.
Problem:
The 'WIDE'-mode can not be selected
Cause:
switch
'WIDE'
at the back panel is set
position
'Disable'
.
Remedy:
Set switch to position
'Enable'
.
Problem:
Discs can not be played. A message to
enter a PIN appears.
Cause:
This disc is locked
Remedy:
Enter a valid PIN number or unlock the
disc
(see
menu
'
Basic
settings
(Preference page
'
).
Note:
In case you have forgotten your PIN
number, enter the menu
'
Basic settings
(Preference page)
/ Password
'
. Then
enter 000 000 twice. The PIN is now reset
to to 000 000.
Summary of Contents for SADV 1250 R HD
