background image

F-26159-5

©

 

Copyright 2008 TAC All Rights Reserved.

3

TYPICAL APPLICATIONS (wiring diagram)

Figure-1 CP-8551 Typical Wiring.

Figure-2 CP-8552 Typical Wiring for Voltage Input.

Figure-3 CP-8552 Typical Wiring for Current Input.

INSTALLATION

Inspection

Inspect the package for damage. If damaged, notify the appropriate carrier immediately.
If undamaged, open the package and inspect the device for obvious damage. Return 
damaged products.

Requirements

Wiring diagrams.

Tools (not provided):

– Screwdriver for mounting screws.
– Drill and drill bit for mounting screws.

Appropriate accessories.

Two (2) # 6 mounting screws (not provided).

M-636 4 in. T and B wire tie (not provided).

Training: Installer must be a qualified, experienced technician.

CP-8551

M

B

M

3 to 15 psig

(21 to 103 kPa

to controlled device

(direct acting)

+

+4 to 20 mA Current Input Signal

Signal Common

CP-8552

M

B

M

3 to 15 psig

(21 to 103 kPa

to controlled device

(direct acting)

+IV1

Signal Common

Voltage Input Signal

Power Common

COM

24 Vac/dc

24H

1

1

When multiple CP-8552s or other devices are powered 
by a common source, uniform wiring polarity must be 
maintained between all 24H and COM terminals. Check 
to ensure that the controller’s COM terminal is not 
connected to any other ground reference.

1

2

3

CP-8552

M

B

M

3 to 15 psig

(21 to 103 kPa

to controlled device

(direct acting)

COM

+IV1

Signal Common

+4 to 20 mA Current Input Signal

1

2

3

Summary of Contents for CP-8551









Reviews: