background image

1 General notes

1.1 Structure of the operating instructions

Before installation and start-up, read this manual carefully to ensure correct use!
We emphasize that these operating instructions apply to speci

c units only, and are in 

no way valid for the complete system!
Use these operating instructions to work safely with and on the device. They contain 
safety instructions that must be complied with as well as information that is required for 
failure-free operation of the device.
Keep these operating insturctions together with the device. It must be ensured that all 
persons that are to work on the device can refer to the operating instructions at any time.

1.2 Target group

The operating instructions address persons entrusted with planning, installation, com-
missioning and maintenance and servicing and who have the corresponding quali

ca-

tions and skills for their job.

1.3 Exclusion of liability

To allow for future developments, construction methods and technical data given are 
subject to alteration. We do not accept any liability for possible errors or omissions in the 
information contained in data, illustrations or drawings provided.
We accept no liability for damage caused by misuse, incorrect use, improper use or as a 
consequence of unauthorized repairs or modi

cations.

1.4 Copyright

These operating instructions contain copyright protected information. The operating 
instructions may be neither completely nor partially photocopied, reproduced, translated 
or put on data medium without previous explicit consent. Infringements are liable for 
damages. All rights reserved, including those that arise through patent issue or registra-
tion on a utility model. 

2 Safety instructions

Mounting, electrical connection, and start-up operation may only be carried out by 
an electrical specialist in accordance with electrotechnical regulations (e.g. DIN 
EN 50110 or DIN EN 60204)!

Persons entrusted with the planning, installation, commissioning and maintenance 
and servicing in connection with the device must have the corresponding quali

-

cations and skills for these jobs. In addition, they must be knowledgeable about 
the safety regulations, EU directives, rules for the prevention of accidents and the 
corresponding national as well as regional and in-house regulations.

Operating Instructions 

TCA 150D

General notes

L-BAL-E119-GB 1318 Index 002

Part.-No. 00163357-GB

4/17

Summary of Contents for TCA 150D


















Reviews: