background image

                                                   

Synway Information Engineering Co., Ltd

 

functions available on a single board. 

z

 

On-board SIMM Slots 

Fit modules to board. Contacts on both sides of the SIMM slots greatly improve 
connection and ease installation. 

z

 

Teleconferencing 

The flexible distributed conferencing system sets no limit on the number of 
simultaneous conferences and participants in each conference, allows monitoring 
and recording of the whole conference and each individual speaker. 

z

 

RJ11 and DB44 Connectors Available 

A rear connection panel has eight 4-pin RJ11 jacks and a 16-way DB44 connector 
which can be directly connected to phone lines via a proper arrangement of lines 
and cables, making connection easy and malfunctions rare. 

z

 

Optional Internal/External Ringing Current & Battery Feed Power Supply 

The external ringing current & battery feed power supply provides station modules 
with battery feed, and enables the phones which are linked to station channels to 
ring. 

The ringing current module which may be optionally built on the rear connection 
panel supplies the internal ringing current and battery feed provided that it is 
working with the 48V IPC power supply. 

z

 

Programmable Tone Detector 

Detects single or dual tones at any frequency, offering facility for use with a variety 
of PBXes and key telephone systems. 

z

 

Specialized Driver Algorithm 

Uses SPECDial – a specialized driver algorithm - to perform a complete automatic 
dial process through analog lines. Accurately identifies called-party statuses and 
precisely distinguishes an answering machine from a fax machine that is 
responding at the remote end. 

z

 

Echo Cancellation 

The self-adaptive echo cancellation feature effectively eliminates echoes under 
various conditions, which cancels out the effect of voice playback on DTMF and 
busy tones detection, avoids self-excited oscillation and howling, and minimizes the 
possibility of registering wrong DTMF and busy tones in a conference call. 

z

 

Various CODECs Support 

Offers a large selection of voice CODECs, including hardware-based A-law (G.711), 

μ

-law, IMA-ADPCM, software-based 16-bit linear PCM, MP3 and VOX. 

SHT-16B-CT/cPCI 2.0, SHT-16B-CT/cPCI/FAX (MP3) 2.0 Hardware Manual 

(Version 2.2) 

  Page 2 

Summary of Contents for SHT-16B-CT/cPCI 2.0


























Reviews: