manualshive.com logo in svg

Synway SBO500 SBO Series, User Manual

Share
Download
Synway SBO500 SBO Series User Manual Download Page 53

                                                           

Synway Information Engineering Co., Ltd

 

Access Setting 

Sets the IP addresses which can access the gateway via WEB. By default, all IPs 

are allowed. You can set an IP whitelist to allow all IPs within it to access the 

gateway freely. Also can set an IP blacklist to forbid all IPs within it to access the 

gateway. 

Time to Log Out 

The gateway will log out automatically if it is not operated during a time longer than 

the value of this item, calculated by s, with the default value of 1800. 

SSH 

Sets whether to enable the gateway to be accessed via SSH, with the default value 

of 

No

. 

SSH Port 

The port which is used to access the gateway via SSH. 

Remote Data 

Capture 

After this feature is enabled, you can obtain the gateway data via a remote capture 

tool, with the default value of 

No

. 

Capture RTP 

Sets whether to capture the RTP. Once this feature is enabled, the RTP package will 

also be captured by the selected network. 

FTP 

Sets whether to enable the FTP server, with the default value of 

Yes

. 

SYSLOG 

Sets whether to enable SYSLOG. It is required to fill in 

SYSLOG Server Address

 

and 

SYSLOG Level

 in case SYSLOG is enabled. By default, 

SYSLOG

 is disabled. 

Server Address 

Sets the SYSLOG server address for log reception. 

SYSLOG Level 

Sets the SYSLOG level. There are three options: 

ERROR

, 

WARNING 

and 

INFO

. 

NTP 

Sets whether to enable the NTP time synchronization feature. It is required to fill in 

NTP Server Address

, 

Synchronizing Cycle

 and 

Time Zone

 in case NTP is 

enabled. By default, 

NTP

 is disabled. 

NTP Server Address 

Sets the Server address for NTP time synchronization. 

Synchronizing Cycle 

Sets the cycle for NTP time synchronization. 

Daily Restart 

Sets whether to restart the gateway regularly every day at the preset 

Restart Time

. 

By default, this feature is disabled. 

Restart Time 

Sets the time to restart the gateway regularly. 

System Time 

The system time. Check the checkbox before 

Modify 

and change the time in the 

edit box. 

Time Zone 

The time zone of the gateway. 

3.7.3 IP Routing Table 

IP Routing Table is used to set the route for the LAN port when these two network ports both 
transport SIP. Thus, the LAN can access some IPs in other different network segment. By default, 
there is no routing table available on the gateway, click 

Add New

 to add them manually. See 

Figure 3-50.

 

SMG SBO Series Gateway User Manual (Version 1.6.3)         

                                      Page 48 

Summary of Contents for SBO500 SBO Series









































































Reviews:

No comments

Brands by name

Popular brands

Load more brands