Functional overview (cont’d)
Before you start
Using a remote control
Keep in mind the following when using the remote
control:
• Make sure that there is no obstacle between the
remote control and the remote sensor of the
unit.
• Remote operation may become unreliable if
strong sunlight or fluorescent light is on the
remote sensor of the unit.
• Remote control for different devices can inter-
fere with each other. Avoid using remote control
for other equipment located close to the unit.
• Replace the batteries when you notice a fall-off
of the operating range of the remote control.
• The maximum operable ranges from the unit are
as follows.
-
Beeline:
approx. 23 feet (7m)
-
Either side of the center:
approx.
1
6 feet (5m) within 30°
-
Above:
approx.
1
6 feet (5m) within
1
5°
-
Below:
approx.
1
0 feet (3m) within 30°
Installing batteries in the remote control
Install two “AA” size batteries (supplied), matching
their polarity to those indicated inside battery com-
partment of the remote control.
1
Note:
Incorrect use of batteries can result in hazards such
as leakage and bursting. Please follow the instruction
below:
• Do not mix new and old batteries together.
• Do not use different kinds of batteries together.
Although they may look similar, different batteries
may have different voltages.
• Make sure that the plus and minus ends of each
battery match the indications in the battery com-
partment.
• Remove batteries from equipment that is not going
to be used for a month or more.
• When disposing used batteries, please comply with
governmental regulations or public rules for envi-
ronmental protection that apply in your country
or area.
• Do not recharge, short-circuit, heat, burn or disas-
semble batteries.
10
2
3
Because this product is a combination of a VCR and a DVD recorder, you must select first which com-
ponent you wish to operate with
[OUTPUT SELECT]
.
Press
[VCR]
on the remote control.
(Verify that the VCR indicator is lit.)
VCR MODE
Press
[DVD]
on the remote control.
(Verify that the DVD indicator is lit.)
DVD MODE
The VCR/DVD recorder Switching
Notes:
• Pressing only
[OUTPUT SELECT]
on the
front panel DOES NOT switch the mode of the
remote control.You MUST select the correct
mode on the remote control.
• You cannot switch to another mode (DVD or
VCR) during in the timer-standby mode.
• Pressing
[REC/OTR]
(DVD) or
[REC/OTR]
(VCR) on the remote control switches immedi-
ately its respective mode so that you can start
recording directly on the appropriate media.
POW
ER
REW
F.FW
D
PLA
Y
REC
ORD
CHA
NNE
L
STO
P
PLA
Y
REC
ORD
S-VID
EO
VID
EO
L - A
UDIO
- R
OUT
PUT
SEL
ECT
VCR
DVD
OPE
N/C
LOS
E
STO
P/EJ
ECT
SK
IP
REC
PAU
SE
P
ENTE
R
ME
NU
PLA
Y L
IST
TO
P M
EN
U/
OR
IGIN
AL
k
K
FW
D
g
STO
P
C
PL
AY
B
RE
V
h
H
G
Remote
control
Within about
23feet (7m)
30˚
30˚
DUB
BING
STOP
POWER
T-SET
TIMER PROG.
SKIP
SKIP
OPEN/CLOSE
SPACE
1
2
3
4
5
6
7
8
0
9
CH
VIDEO/TV
SLOW
PAUSE
.@/:
ABC
DEF
GHI
JKL
MNO
PQRS
REC/OTR
DISPLAY
TUV
WXYZ
DVD
REC/OTR
REC SPEED
ZOOM
SEARCH
VCR
SETUP
CM SKIP
RETURN
MENU/LIST
TOP MENU
DUBBING
REC MONITOR
CLEAR
ENTER
PLAY
AUDIO
POWER
REW
F.FWD
PLAY
RECORD
CHANNEL
STOP
PLAY
RECORD
S-VIDEO
VIDEO
L - AUDIO - R
OUTPUT SELECT
VCR
DVD
OPEN/CLOSE
STOP/EJECT
DUBBING
OUTPUT SELECT
VCR
DVD
OUTPUT
SELECT button
DVD indicator
VCR indicator
DVD button
VCR button
E9621UD_EN/SP2.qx3 05.7.25 2:42 PM Page 10