Symmetricom TimeProvider 500 series Reference Manual Download Page 20

Page: 20 / 165

TMSL 097-44018-26

Issue 2: Sep 99

Page 20

COMMAND CODE: CONN-COM

PURPOSE

CONNECT COMMUNICATION

This command initiates a connection sequence on the specified communication port. This command must
be entered on a communication port other than the one specified in the command where the PAD is lo-
cated.

INPUT FORMAT

CONN-COM:[<tid>]:<aid>:<ctag>::[comtype];

EXAMPLE

Input:

CONN-COM::COM-1:134::X25;

Response:

SANJOSE-114 1997-12-08 15:04:13

134 COMPLD

;

This example, tagged as command 134, requests a connection on communication port 1 using PAD as the
communication device.

parameter

value

meaning

aid

COM-1

communication port 1 (backplane D connector)

COM-2

communication port 2 (backplane D connector or front panel RJ connector)

COM-3

communication port 3 (backplane D connector)

comtype

X25

PAD (sets configuration for Black Box Corporation’s X.25 PAD-8 only with the
following settings:

a. drops call if idle time is greater than 1 minute
b. fixed destination id

MODEM

modem (sets RS232 control leads to communicate with any Hayes-compatible
modem with autodial)

Summary of Contents for TimeProvider 500 series






































































































































































Search results

Summary of Contents for TimeProvider 500 series

Reviews:

Related manuals for TimeProvider 500 series

Brands by name

Popular brands

Symmetricom TimeProvider 500 series, Reference Manual

Search results

Summary of Contents for TimeProvider 500 series

Reviews:

Related manuals for TimeProvider 500 series

Brands by name

Popular brands