Symmetricom TimeProvider 500 series Reference Manual Download Page 143

Page: 143 / 165

Issue 2: Sep 99

TMSL 097-44018-26

Page 143

COMMAND CODE: SET-REPTMODE-PORT

PURPOSE

SET REPORT MODE PORT

This command sets the message type (REPT-ALM-PORT or REPT-ALM-EQPT) used to report autono-
mous port-alarm messages.

INPUT FORMAT

SET-REPTMODE-PORT:[<tid>]::<ctag>::<modetype>;

Note:

Automatic equipment-alarm messages are always reported as REPT-ALM-EQPT messages.

EXAMPLE

Input:

SET-REPTMODE-PORT:::119::ALW;

Response:

SANJOSE-114 1997-12-08 15:04:13

119 COMPLD

;

This example, tagged as command 119, sets automatic port-alarm messages to be reported as REPT-
ALM-PORT messages.

modetype

meaning

ALW

automatic port-alarm messages are reported as REPT-ALM-PORT
messages

INH

automatic port-alarm messages are reported as REPT-ALM-EQPT
messages

Summary of Contents for TimeProvider 500 series






































































































































































Search results

Summary of Contents for TimeProvider 500 series

Reviews:

Brands by name

Popular brands

Symmetricom TimeProvider 500 series, Reference Manual

Search results

Summary of Contents for TimeProvider 500 series

Reviews:

Brands by name

Popular brands