background image

SYMEO Local Positioning Radar System 

LPR-1DHP 

Product Documentation 

  

Overview Safety

 

Copyright © Symeo GmbH 2012 

 

 

Page 2 of 40 

 

Content 

1

 

OVERVIEW SAFETY .................................................................................................. 6

 

1.1

 

Safety Instructions .................................................................................................... 6

 

1.2

 

Installation ................................................................................................................. 6

 

1.3

 

Repairs....................................................................................................................... 6

 

1.4

 

Transport and Storage .............................................................................................. 6

 

1.5

 

Power Supply ............................................................................................................ 7

 

1.6

 

Setup and Operation ................................................................................................. 7

 

1.7

 

System Extensions and Accessories ...................................................................... 7

 

1.8

 

Additional Instructions Regarding LPR-1DHP station............................................ 8

 

1.9

 

Important Information to User .................................................................................. 8

 

2

 

OVERVIEW OF THE LPR-1DHP SYSTEM ................................................................ 9

 

2.1

 

Data sheet of LPR-1DHP Station ............................................................................ 10

 

2.2

 

Opening angle LPR-1DHP station .......................................................................... 10

 

2.3

 

Mounting position of the LPR-1DHP stations ....................................................... 11

 

3

 

COMPONENT SETUP OF THE LPR-1DHP STATION ............................................. 12

 

3.1

 

Overview .................................................................................................................. 12

 

3.2

 

Front element .......................................................................................................... 13

 

3.2.1

 

LED display ............................................................................................................... 13

 

3.2.2

 

Other parts ................................................................................................................ 13

 

3.3

 

Rear elements ......................................................................................................... 14

 

3.3.1

 

LPR-1DHP station with TCP/IP interface................................................................... 14

 

4

 

ELECTRICAL CONNECTIONS ................................................................................ 15

 

4.1

 

LPR-1DHP station with TCP/IP interface ............................................................... 15

 

4.1.1

 

Electrical connection ................................................................................................. 15

 

4.1.2

 

Mode of operation ..................................................................................................... 15

 

4.2

 

LPR-1DHP configuration with USB interface ........................................................ 16

 

4.2.1

 

Electrical connection ................................................................................................. 16

 

4.2.2

 

Mode of operation ..................................................................................................... 16

 

Summary of Contents for LPR-1DHP









































Reviews: