manualshive.com logo in svg

Symbol Hotspot LS 2100, Product Reference Manual

Share
Download
Symbol Hotspot LS 2100 Product Reference Manual Download Page 92

6-19

RS-232 Interface

Stop Bit Select

The stop bit(s) at the end of each transmitted character marks the end of transmission of 
one character and prepares the receiving device for the next character in the serial data 
stream. The number of stop bits selected (one or two) depends on the number the receiving 
terminal is programmed to accommodate. Set the number of stop bits to match host device 
requirements.

*

1 Stop Bit

2 Stop Bits

ASCII Format

This parameter allows the scanner to interface with devices requiring a 7-bit or 8-bit ASCII 
protocol.

7-Bit

*

8-Bit

Summary of Contents for Hotspot LS 2100































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands