manualshive.com logo in svg

Symantec netbackup 5030, Troubleshooting Manual, Page: 48 / 69

Share
Download
Symantec netbackup 5030 Troubleshooting Manual Download Page 48

To verify that a drive is faulty

Caution:

The drive status LED must be solid amber before you remove a drive from

the appliance. Data loss and corruption can occur when a drive is disconnected
inappropriately.

1

Make sure that the drive status LED is amber.

2

Pull open the green handle on the drive cover to disengage the drive from
the slot.

Note:

You can gently pull the drive forward about an inch (2.4 cm) to ensure

that the drive is disengaged.

3

Remove the disk drive completely.

4

Install a new drive from Symantec.

Caution:

You must use a drive that is properly set up for the NetBackup RAID.

5

After the new drive spins up, wait for approximately three minutes.

6

Check the disk drive LEDs and do the following:

■

If the activity LED is green, the fault is resolved.

■

If the status LED is still amber, escalate as needed.

Troubleshooting a system drive that the management
software does not identify

You can use this procedure when a system disk drive is not found and reported
in any of the following management tools:

■

Administrative Web UI or NetBackup Appliance Web Console

■

Appliance shell menu

■

Symantec Remote Management tool

The possible causes include the following:

■

Improperly installed disk drive. The connector on the drive is not properly
mated with the connector inside the chassis.

Troubleshooting scenarios

Troubleshooting a system drive that the management software does not identify

48

Summary of Contents for netbackup 5030






































































Reviews:

No comments