background image

 

 

3989108 

IMPORTANT: READ CAREFULLY BEFORE INSTALLING THE FIXTURE. RETAIN FOR FUTURE REFERENCE. 

 

GENERAL: 

Upon receipt of the fixture, thoroughly inspect for any freight damage which should be brought to the attention of the delivery 

carrier. 

 

WIRING DIAGRAM 

 

 

 

 

 

 

 

 

 

   PENDANT MOUNTING: 

 

 

1. 

Disassemble the driver box cover by removing the 4 hex head screws keeping them for later. Figure 1 

2. 

Loosen and remove the 3/4 plug on the top of the driver box cover. Figure 2 

3. 

Fix the driver box cover on the ¾” pipe. Figure 3 

4. 

Hang the safety cord attached to the driver to the hook inside the luminaire’s main body. Figure 4 

5. 

Make all wiring connections in accordance with NEC and local codes; If the fixture is equipped with sensor, adjust the sensor 

settings. Take relevant waterproof measures after the wires are connected. Figure 5 

6. 

Fasten and close the luminaire. Figure 6 

7. 

Replace the screws removed in step 1, the product is installed. Figure 7 

     

 

   

  

 

    

FIGURE 1            

    FIGURE 2  

 

        FIGURE 3   

  

     FIGURE 4 

 

    

 

 

 

   

 

    

 

          FIGURE 5         

 

            FIGURE 6       

 

             FIGURE 7 

 

 

Summary of Contents for ValueLED











Reviews: