Correct method to detach bracket
If you accidentally attach the bracket before installation, carefully remove it as shown.
Remove from both ends at the same time.
Do not use force to pull the bracket from the
middle.This may cause damage!
Mode setting
Chose a mode before mounting the light.
a) “Switch” mode
Use the wall switch to adjust colour temp by setting the mode to
Switch
.
1. Set the mode to
Switch
.
2.
Install the light fixture. See section “Cut-out mount” or “Surface
mounting”.
3.
Switch the wall switch “ON → OFF → ON” to cycle through colour
temperatures:
CW
(cool white) →
NW
(neutral white) →
WW
(warm white).
b) “Preset” mode
Set the colour temperature at the light so the wall switch just switches the light ON/OFF.
1. Set the mode to:
CW
(cool white),
NW
(neutral white),
WW
(warm white).
2.
Install the light fixture. See section “Cut-out mount” or “Surface mounting”.
3. Switch the wall switch ON.
Cut-out mount
Risk of electric shock!
• Before installation, maintenance, or removal, always switch the electricity supply and corre-
sponding circuit breaker and/or automatic fuse OFF.
• Secure against unauthorized restart, e.g. by installing a warning sign.
• Check the power circuit for any remaining voltage using an appropriate measuring device.
a) Installation
•
The bracket can fit irregular shapes.
• If you are creating a new cut-out, the opening should be 55 -170 mm wide.
•
Attach the sliding springs to the bracket as shown above, then adjust to fit the cut-out.
Insert the bracket with springs attached into the
cut-out as shown.
The space between springs should be
centered on the bracket.
1. Attach the safety wire to the light and bracket.
2. Connect the light to the power supply.
3.
Press the light fixture onto the bracket.
Operating Instructions
3 CCT Clip-on LED Ceiling
Light, 18 W
Item No. 2335669
Intended use
The product is an LED ceiling light. It can be mount-
ed over a cut-out or onto a surface.
It is intended for indoor use only. Do not use it out-
doors. Contact with moisture, e.g. in bathrooms,
must be avoided under all circumstances.
For safety and approval purposes, you must not re-
build and/or modify this product. If you use the prod-
uct for purposes other than those described above,
the product may be damaged. In addition, improper
use can result in short circuits, fires, electric shocks
or other hazards. Read the instructions carefully and
store them in a safe place. Make this product avail-
able to third parties only together with its operating
instructions.
This product complies with the statutory national and
European requirements. All company names and
product names are trademarks of their respective
owners. All rights reserved.
Delivery content
• Ceiling light
• Accessories pack
(2x springs, 2x wall plugs, 3x screws)
• Operating instructions
Up-to-date operating instructions
Download the latest operating instructions at
www.conrad.com/downloads or scan the QR code
shown. Follow the instructions on the website.
Explanation of symbols
The symbol with the lightning in the
triangle is used if there is a risk to your
health, e.g. due to an electric shock.
The symbol with the exclamation mark in
the triangle is used to indicate important
information in these operating instruc-
tions. Always read this information care-
fully.
The product is designed according to
protection Class II.
The product must only be used in dry,
enclosed indoor areas. The product
must not become damp or wet, other-
wise there is a risk of a fatal electrical
shock!
This symbol indicates that this product
should not be used with an external dim-
mer.
The arrow symbol indicates special in-
formation and advice on operation.
Safety instructions
Read the operating instructions
carefully and especially observe
the safety information. If you do not
follow the safety instructions and
information on proper handling in
this manual, we assume no liability
for any resulting personal injury or
damage to property. Such cases will
invalidate the warranty/guarantee.
a) General information
• The device is not a toy. Keep it out of the reach
of children and pets.
• Do not leave packaging material lying around
carelessly. This may become dangerous playing
material for children.
• Protect the appliance from extreme tempera-
tures, direct sunlight, strong jolts, high humidity,
moisture, flammable gases, steam and solvents.
• Do not place the product under any mechanical
stress.
• If it is no longer possible to operate the product
safely, take it out of operation and protect it from
any accidental use. Safe operation can no longer
be guaranteed if the product:
- is visibly damaged,
- is no longer working properly,
- has been stored for extended periods in poor
ambient conditions or
- has been subjected to any serious transport-
related stresses.
• Please handle the product carefully. Jolts, im-
pacts or a fall even from a low height can dam-
age the product.
• Consult an expert when in doubt about the op-
eration, safety or connection of the appliance.
•
Maintenance, modifications and repairs must
only be completed by a technician or an author-
ised repair centre.
• If you have questions which remain unanswered
by these operating instructions, contact our tech-
nical support service or other technical person-
nel.
b) LED light
Attention, LED light:
• Do not look directly into the LED light!
• Do not look into the beam directly or with optical
instruments!
c) Mounting
• When drilling, or tightening screws, make sure
there are no cables, wires, or pipes located be-
neath the surface.
• Inadvertently piercing through electric cables can
cause life-threatening electric shock!
d) Electrical
Caution, safety hazard!
The product should only be installed by people
with relevant electrical knowledge and experi-
ence! *)
• If it is not installed properly, you risk:
- your own life
- the life of user of the electrical device
• If it is not installed properly, you risk severe dam-
age to property, e.g. by fire.
• You face the risk of personal liability for personal
injury and material damage.
• Always consult an electrician!
*) Technical knowledge required to perform the
installation:
• For the installation, the following specialist
knowledge is required in particular:
-
The “Five safety rules”: Disconnect from the
mains; protect against accidental switch-on;
ensure there is no voltage; earth and short-
circuit; cover or protect adjacent live parts
- Use of suitable tools, measuring devices and
personal protective equipment, where neces-
sary
- Analysis of measurement results
- Use of electrical installation materials to meet
the requirements for disconnection
- IP protection ratings
- Installation of electrical installation materials
- Type of power supply (TN system, IT system,
TT system) and the corresponding connection
criteria (classic earthing, protective earthing,
necessary additional measures etc.)
If you are not a professional, do not do it yourself,
have it performed by a specialist.
