Operating elements
1
9
2
8
3
7
4
6
5
1 Filter
2 Display
3 Control panel
4 Handle
5 Air outlet
6 Water tank
7 Mains cable with mains plug
8 Castor
9 Front panel
Control panel
SWING
W.F
TIMER
SETTINGS
H
L
POWER
Button / LED
Function
W.F
Full water tank warning
SWING
Swinging air outlet
TIMER
Programming the power-on or power-off time
SETTINGS
Setting the desired air humidity level
H L
Setting the fan speed
POWER
On/off switch
Positioning
•
Place the product on a flat, horizontal and stable surface.
• Leave a distance of at least 20 cm between the device and any walls, furniture, etc.
Operation
a) Connection
Connect the power plug to a common household power outlet. The device will emit a signal
sound. The green
POWER
LED lights up steadily. The product is in standby mode.
b) Switching on/off
Press the
POWER
button to switch the product on or off. When switched on, the display will
show the current ambient humidity. In addition to that, one of the fan LEDs (
H or
L
) lights up.
c) Setting the fan speed
Press the button marked with the fan symbol to select one of the two settings. The respective
LED lights up permanently.
• H = high
•
L
= low
d) Setting the air humidity level
Press the
SETTINGS
button to set the air humidity level within a range of 40 to 80 % and in
increments of 5 percent. The LED corresponding to the button lights up briefly. The display will
briefly show the set value. After that, the display will show the current ambient humidity level
again.
e) Timer
Programming the power-on time
•
In order to use this function, the product must be switched off (standby mode).
• Press the
TIMER
button to set the time within a range of 1 to 24 hours and in increments of
1 hour. The LED corresponding to the button lights up permanently. The display will show
the set value.
• If you select a value of 10 hours, the product will turn on automatically after 10 hours.
• In order to deactivate the automatic switch-on function, switch the product on manually or
reset the timer to 00.
Programming the power-off time
• In order to use this function, the product must be switched on.
• Press the
TIMER
button to set the time within a range of 1 to 24 hours and in increments of
1 hour. The LED corresponding to the button lights up permanently. The display will show
the set value.
• If you select a value of 10 hours, the product will turn off automatically after 10 hours.
• In order to deactivate the automatic switch-off function, switch the product off manually or
reset the timer to 00.
The system will keep the programmed time, if the operation is being deactivated by
the automatic defrost function.
f) Swinging air outlet
• Press the
SWING
button to swing the air outlet upwards or downwards. The LED
corresponding to the button lights up permanently.
• Press the button again to deactivate this function. The LED turns off.
Display
• When the current ambient humidity drops below a value of 35 %, the display will show
35
.
• When the current ambient humidity exceeds a value of 95 %, the display will show
95
.
Emptying the water tank
• Once the water tank is full, the red
W.F
LED lights up. On top of that, the product will beep
15 times.
• Switch off the product and disconnect the mains plug from the mains.
• Pull out the water tank completely.
• Empty the water tank.
• Reinstall the water tank.
Make sure the floating device (overflow protection mechanism) at the rear left of the
water tank is properly installed. Otherwise there is a risk of water overflowing.
If the water tank has not been installed properly, the red
W.F
LED will remain on and
the product will not work.
Continuous water drainage
This function requires a separately available drainage hose with an internal Ø of
10 mm and an external Ø of 13 mm.
• Switch off the product and disconnect the mains plug from the mains.
• Pull out the water tank completely.
• Remove the round cap located in the upper right area of the water tank. To do so, use a
suitable tool (e.g. cutter, knife).
• Guide the hose through the opening.
• Attach the hose to the black drainage nozzle inside the product. If needed, secure the hose
with a suitable clip.
•
Position the other end of the hose in such a way that water can discharge (e.g. outdoors or
drainage hole in the floor). The water must discharge in a downward direction.
• Reinstall the water tank.
Installing the carbon filter
• Switch off the product.
•
Carefully flip the front panel open.
•
Remove the air filter frame from the rear of the front panel.
•
Place the carbon filter on the rear side of the air filter frame (the side facing the compressor).
•
Reinsert the air filter frame together with the carbon filter. Make sure the guiding rails hold
the carbon filter in position.
• Then close the front panel.
The carbon filter must be replaced after approx. 1‑2 years.
