Swann MF-1F, Installation Manual

Page: 4 / 12

Contents (Wall Mount Units)
Laundry Tub
Filler Brackets (Right and Left)
Filler Bracket Mounting Screw (Qty 2)
Wall Mounting Plate
Screws for Wall Mounting Plate (Qty 3 or 6)
Wall Anchors for Wall Mounting Plate (Qty 3 or 6)
Purchased Items
Faucet
Flexible Hot and Cold Water Supply Lines
PVC Trap Kit
PVC Tailpiece
1/4” x 1-1/2” Tapcon Screws (optional for wall mount units
only - for concrete wall installation)
Floor Anchors and Bolts (optional)
Required Tools and Safety Equipment
Safety Glasses
Hearing Protection
Hammer
Adjustable Pliers
Adjustable Wrench
Phillips Screwdriver
Flat Blade Screwdriver
Tape Measure
Hacksaw (Cutting tail piece to length)
Level
Hammer Drill and Carbide Drill Bit (for wall mount
installation into concrete or to fasten the legs to the floor)
Unpackaging
Use care when opening the box so that you do not damage
the product.
This product is shipped to you or your retail center after
careful inspection. After purchasing the product, carefully
unbox and inspect the product for any shipping damage that
may have occurred. If damage is found, report it
immediately to the store of purchase. Installation of a
damaged product will void the warranty.
Make sure the product is the correct size and confirm that
all parts have been included before beginning installation.
Floor mount models are shipped with four legs and leveling
hardware. The floor mount models DO NOT have right and
left side filler brackets like the wall mount models.
Please use the model number located on the side of the
box when contacting us with questions concerning the
installation of this product.
Helpful Hints
Read all instructions carefully BEFORE starting the
installation. Familiarize yourself with the various parts of
the kit.
Store unused materials away from the work area to prevent
accidental damage.
If the product is placed over a garage or on an outside wall,
care must be taken to ensure that the shower plumbing is
properly insulated from cold temperatures.
Disclaimer
The information contained in this Installation Instruction is
given free of charge. It is based upon technical data which
we believe to be reliable and is intended for use, by
persons having knowledge of this technical area, at their
own discretion and risk. The Swan Corporation assumes
no responsibility for results obtained or damage incurred
from the use of this material either in whole or in part by the
buyer.
This manual will give you basic step-by-step instructions for
the installation of the product that will work in most types of
installations. If you have an installation application that is
not covered in this manual, before beginning the
installation , please call your local Swan distributor or
contact the Swan Corporation directly for additional
information about your application.
Follow all installation instructions. Failure to follow these
instructions could result in personal injuries, water damage,
or other damage to floors, pipes, walls, or other portions of
your building or home.
Quick Reference Assembly
1. Prior to installation of the laundry tub, first attach the legs
to floor mount models (Step 1a) or attach the filler
brackets to the wall mount models (Step 1b). Refer to the
specific section in this manual for detailed instructions.
2. Attach the wall mounting plate to the wall. (Step 2a, 2b, or
2c).
3. Finally, install faucet and P-trap onto the laundry tub.
4. Install laundry tub.
5. Anchor floor mount units to the floor (optional).
6. Install splash guard (optional).
1. Attach Legs / Filler Brackets
1a. Attach Metal Legs — MF-1F and
MF-2F (Single and Double Bowl Models)
1. Place the laundry tub upside down on a flat surface.
Protect the top edges of the laundry tub from scratches or
other damage by placing cardboard or other scratch
resistant material on the floor.
LT-032
The Swan Corporation – Swanstone 4 800-325-7008
General Information Installation Procedure
Attach Plastic Legs - MF-4W (Single Bowl Model)
Contents (Wall Mount Units)
Laundry Tub
Filler Brackets (Right and Left)
Filler Bracket Mounting Screw (Qty 2)
Wall Mounting Plate
Screws for Wall Mounting Plate (Qty 3 or 6)
Wall Anchors for Wall Mounting Plate (Qty 3 or 6)
Purchased Items
Faucet
Flexible Hot and Cold Water Supply Lines
PVC Trap Kit
PVC Tailpiece
1/4” x 1-1/2” Tapcon Screws (optional for wall mount units
only - for concrete wall installation)
Floor Anchors and Bolts (optional)
Required Tools and Safety Equipment
Safety Glasses
Hearing Protection
Hammer
Adjustable Pliers
Adjustable Wrench
Phillips Screwdriver
Flat Blade Screwdriver
Tape Measure
Hacksaw (Cutting tail piece to length)
Level
Hammer Drill and Carbide Drill Bit (for wall mount
installation into concrete or to fasten the legs to the floor)
Unpackaging
Use care when opening the box so that you do not damage
the product.
This product is shipped to you or your retail center after
careful inspection. After purchasing the product, carefully
unbox and inspect the product for any shipping damage that
may have occurred. If damage is found, report it
immediately to the store of purchase. Installation of a
damaged product will void the warranty.
Make sure the product is the correct size and confirm that
all parts have been included before beginning installation.
Floor mount models are shipped with four legs and leveling
hardware. The floor mount models DO NOT have right and
left side filler brackets like the wall mount models.
Please use the model number located on the side of the
box when contacting us with questions concerning the
installation of this product.
Helpful Hints
Read all instructions carefully BEFORE starting the
installation. Familiarize yourself with the various parts of
the kit.
Store unused materials away from the work area to prevent
accidental damage.
If the product is placed over a garage or on an outside wall,
care must be taken to ensure that the shower plumbing is
properly insulated from cold temperatures.
Disclaimer
The information contained in this Installation Instruction is
given free of charge. It is based upon technical data which
we believe to be reliable and is intended for use, by
persons having knowledge of this technical area, at their
own discretion and risk. The Swan Corporation assumes
no responsibility for results obtained or damage incurred
from the use of this material either in whole or in part by the
buyer.
This manual will give you basic step-by-step instructions for
the installation of the product that will work in most types of
installations. If you have an installation application that is
not covered in this manual, before beginning the
installation , please call your local Swan distributor or
contact the Swan Corporation directly for additional
information about your application.
Follow all installation instructions. Failure to follow these
instructions could result in personal injuries, water damage,
or other damage to floors, pipes, walls, or other portions of
your building or home.
Quick Reference Assembly
1. Prior to installation of the laundry tub, first attach the legs
to floor mount models (Step 1a) or attach the filler
brackets to the wall mount models (Step 1b). Refer to the
specific section in this manual for detailed instructions.
2. Attach the wall mounting plate to the wall. (Step 2a, 2b, or
2c).
3. Finally, install faucet and P-trap onto the laundry tub.
4. Install laundry tub.
5. Anchor floor mount units to the floor (optional).
6. Install splash guard (optional).
1. Attach Legs / Filler Brackets
1a. Attach Metal Legs — MF-1F and
MF-2F (Single and Double Bowl Models)
1. Place the laundry tub upside down on a flat surface.
Protect the top edges of the laundry tub from scratches or
other damage by placing cardboard or other scratch
resistant material on the floor.
LT-032
The Swan Corporation – Swanstone 4 800-325-7008
General Information Installation Procedure
Contents (Wall Mount Units)
Laundry Tub
Filler Brackets (Right and Left)
Filler Bracket Mounting Screw (Qty 2)
Wall Mounting Plate
Screws for Wall Mounting Plate (Qty 3 or 6)
Wall Anchors for Wall Mounting Plate (Qty 3 or 6)
Purchased Items
Faucet
Flexible Hot and Cold Water Supply Lines
PVC Trap Kit
PVC Tailpiece
1/4” x 1-1/2” Tapcon Screws (optional for wall mount units
only - for concrete wall installation)
Floor Anchors and Bolts (optional)
Required Tools and Safety Equipment
Safety Glasses
Hearing Protection
Hammer
Adjustable Pliers
Adjustable Wrench
Phillips Screwdriver
Flat Blade Screwdriver
Tape Measure
Hacksaw (Cutting tail piece to length)
Level
Hammer Drill and Carbide Drill Bit (for wall mount
installation into concrete or to fasten the legs to the floor)
Unpackaging
Use care when opening the box so that you do not damage
the product.
This product is shipped to you or your retail center after
careful inspection. After purchasing the product, carefully
unbox and inspect the product for any shipping damage that
may have occurred. If damage is found, report it
immediately to the store of purchase. Installation of a
damaged product will void the warranty.
Make sure the product is the correct size and confirm that
all parts have been included before beginning installation.
Floor mount models are shipped with four legs and leveling
hardware. The floor mount models DO NOT have right and
left side filler brackets like the wall mount models.
Please use the model number located on the side of the
box when contacting us with questions concerning the
installation of this product.
Helpful Hints
Read all instructions carefully BEFORE starting the
installation. Familiarize yourself with the various parts of
the kit.
Store unused materials away from the work area to prevent
accidental damage.
If the product is placed over a garage or on an outside wall,
care must be taken to ensure that the shower plumbing is
properly insulated from cold temperatures.
Disclaimer
The information contained in this Installation Instruction is
given free of charge. It is based upon technical data which
we believe to be reliable and is intended for use, by
persons having knowledge of this technical area, at their
own discretion and risk. The Swan Corporation assumes
no responsibility for results obtained or damage incurred
from the use of this material either in whole or in part by the
buyer.
This manual will give you basic step-by-step instructions for
the installation of the product that will work in most types of
installations. If you have an installation application that is
not covered in this manual, before beginning the
installation , please call your local Swan distributor or
contact the Swan Corporation directly for additional
information about your application.
Follow all installation instructions. Failure to follow these
instructions could result in personal injuries, water damage,
or other damage to floors, pipes, walls, or other portions of
your building or home.
Quick Reference Assembly
1. Prior to installation of the laundry tub, first attach the legs
to floor mount models (Step 1a) or attach the filler
brackets to the wall mount models (Step 1b). Refer to the
specific section in this manual for detailed instructions.
2. Attach the wall mounting plate to the wall. (Step 2a, 2b, or
2c).
3. Finally, install faucet and P-trap onto the laundry tub.
4. Install laundry tub.
5. Anchor floor mount units to the floor (optional).
6. Install splash guard (optional).
1. Attach Legs / Filler Brackets
1a. Attach Metal Legs — MF-1F and
MF-2F (Single and Double Bowl Models)
1. Place the laundry tub upside down on a flat surface.
Protect the top edges of the laundry tub from scratches or
other damage by placing cardboard or other scratch
resistant material on the floor.
LT-032
The Swan Corporation – Swanstone 4 800-325-7008
General Information Installation Procedure
Washers (Qty 2)