background image

6-20

ENGINE OIL AND FILTER CHANGE

Change the engine oil and oil filter at
the scheduled time. The oil should be
changed when the engine is warm so
that the oil will drain thoroughly from
the engine. The procedure is as fol-
lows:

1. Place the motorcycle on the side

stand.

2. Remove the oil filler cap 

1

.

3. Place a drain pan under the drain

plugs.

4. Remove the drain plugs 

2

 and

gaskets 

3

 with a wrench and

drain out the engine oil while hold-
ing the motorcycle vertically.

NOTE: Recycle or properly dispose of
used oil.

CAUTION

Hot engine oil and exhaust pipes
can burn you.

Wait until the oil drain plug and
exhaust pipes are cool enough to
touch with bare hands before
draining oil.

WARNING

Children and pets may be harmed
by swallowing new or used oil.
Repeated, prolonged contact with
used engine oil may cause skin
cancer. Brief contact with oil may
irritate skin.

Keep new and used oil and used
oil filters away from children and
pets. To minimize your exposure
to used oil, wear a long-sleeve
shirt and moisture-proof gloves
(such as dishwashing gloves)
when changing oil. If oil contacts
your skin, wash thoroughly with
soap and water. Launder any
clothing or rags if wet with oil.
Recycle or properly dispose of
used oil and filters.

Summary of Contents for VZR1800/BZ
























































































































Reviews: