background image

21

TRIM TAB ADJUSTMENT

This adjustment is used to compensate for the
possible  tendency  of  your  boat  to  veer  slightly
to  port  or  starboard.  This  tendency  could  be
due  to  such  things  as  propeller  torque,  motor
mounting position, etc.

To adjust the trim tab:
1. Loosen the bolt 

A

 that holds the trim tab in

place.

2. If  the  boat  tends  to  veer  to  port,  move  the

rear end of the trim tab toward the port side.
If the boat tends to veer to starboard, move
the starboard side.

3. Tighten  the  bolt  that  holds  the  trim  tab  in

place.

After adjusting the trim tab, check to see if the
boat still tends to veer to one side. If necessary,
readjust the trim tab.

CONTROL HANDLE ADJUSTMENT

The  control  handle  friction  and  control  handle
detent  force  can  be  adjusted  to  suit  operator’s
preference.  The  control  handle  friction  adjust-
ment will change the overall effort to move the
control handle. This will help prevent undesired
movement of the control handle in rough water
conditions.  Consult  your  authorized  Suzuki
marine dealer to adjust the control handle fric-
tion and detent force.

IDLE SPEED ADJUSTMENT

The  idle  speed  has  been  factory  adjusted
between 600 – 700 r/min in neutral.

NOTE:
If idle speed cannot be set within the specified
range,  contact  your  authorized  Suzuki  Marine
Dealer.

Type

Adjustable item

A

Friction and detent force

B

Friction

Type A

1 LEV

ER

SELE

CT

THRO

TTLE

ONLY

SELE

CT

THRO

TTLE

ONLY

SELECT

THROTTLE

ONLY

Type B

Summary of Contents for DF250AP





























































































Reviews: