background image

Suzhou Lily Tech CO., Ltd.

7

1

Temperature
sensor faulty

Real time

0s

6s

Auto

Alarm output on, off temperature control, the other
remains.

2

Humidity
sensor faulty

Real time

0s

6s

Auto

Alarm output on, off humidity control, the other
remains.

3

High

temp.

Over

limit

alarm

Real time

0s

5s

Auto

Alarm output on, high temperature over limit protection
on, the other remains.

4

low

temp.

Over

limit

alarm

Real time

0s

5s

Auto

Alarm output on, the other remains.

5

High
humidity
Over

limit

alarm

Real time

0s

5s

Auto

Alarm output on, high humidity over limit protection
on, the other remains.

6

Low humidity
Over

limit

alarm

Real time

0s

5s

Auto

Alarm output on, the other remains.

7

Touched

IC

communicatio
n faulty

Real time

0s

5s

Auto

Notes:

1. Read the instruction carefully, Electrical wiring must be manipulated by certified electrician.Wrong power supply may damage the

device and system seriously.

2. Use this product should be avoided in humid environments or with corrosive gases and strong magnetic field applications, in these

occasions may affect the use of the normal operation of the thermostat.

3.This product has been strictly tested before leaving the factory, as a result of quality problems The company warranty for one year, the

responsibility is limited to the sale of the product itself. Damage caused by improper use is not covered by warranty.

Summary of Contents for ZL-7901A









Reviews: