background image

P Line Maritim HMI

Important Notes

7

1 Important Notes

1.1

Symbole

The symbols in this manual are used to draw your attention on notes and dangers.

1.2

Safety Notes

Read this manual carefully before using the operating device. Keep this man-
ual in a place where it is always accessible to all users.

Proper transportation, handling and storage, placement and installation of this 
product are prerequisites for its subsequent flawless and safe operation.

This user manual contains the most important information for the safe opera-
tion of the device.

The user manual, in particular the safety notes, must be observed by all per-
sonnel working with the device.

Observe the accident prevention rules and regulations that apply to the oper-
ating site.

Installation and operation must only be carried out by qualified and trained 
personnel.

This is the safety alert symbol. It is used to alert you to potential personal injury 
hazards. Obey all safety messages that follow this symbol to avoid possible in-
jury or death.

DANGER

This indicates a hazardous situation which, if not avoided, will result in death or 
serious injury.

WARNING

This indicates a hazardous situation which, if not avoided, could result in death 
or serious injury.

CAUTION

This indicates a hazardous situation which, if not avoided, could result in minor 
or moderate injury.

NOTICE

This symbol together with the signal word NOTE and the accompanying text 
alert the reader to a situation which may cause damage or malfunction to the 
device, hardware/software, or surrounding property.

This symbol and the accompanying text provide the reader with additional infor-
mation or refer to detailed sources of information.

Summary of Contents for TPEM070ZGW















































































Reviews: