background image

Disposal Instructions

All components should be broken down into categories of:

1. 

Mild steel

 - all swing frames, Playzone, Toddlerzone, Teenzone activities, deck frames and springie frames.

2. 

Stainless Steel

 - all slides, mirror panels.

3. 

Aluminium

 - all Playzone and Toddlerzone posts and Playzone post caps.

4. 

Galvanised steel

 - all chains and Teenzone posts.

5. 

Moulded rubber products without steel centres

 - all Toddlerzone caps and edge details.

6. 

Timber

 - all natural timber, plywood and mdf panels.

Wherever possible these materials should be taken to specialist recycling organisations and recycled. 

In some cases where composite materials are used then disposal at land fill sites is the only alternative such as:

7. 

Moulded rubber products encasing steel centres

 - all seats, deck tops, duo/dizzy disc tops.

8. 

High pressure laminate

 - all Toddlerzone, Playzone panels.

9. 

Steel core polypropylene rope

 - all scramble nets, space nets, Playzone/Toddlerzone ropes and rope bridges.

Recommended Regular Inspection and Maintenance

 

 

 

 

 

 

 

 

 

 

 

Interval (days)

 

 

 

 

 

 

 

 

 

 

  7 

14 

28 

56     365

Check stability of handrail and centre pole, tighten connections if 

required.

Check frame at ground level for corrosion and/or rot.

Replace any defective parts.

Check all painted elements for damage, rub down and re-paint or

replace as required.

Check panels for wear or damage. Replace as required

Check drive and guide wheels for wear and smooth running,

lubricate or replace as required.

Check rubber parts and deck for wear and/or damage, replace as 

required.

Visual inspection, remove any debris and check for correct

operation.

Check perimeter gap, adjust if required.

Check slide chutes for smoothness and any foreign elements,

remove any found.

Check rubber safety surfaces for damage and poor performance,

repair or replace if required.

Check loose fill safety surfaces, remove any foreign elements, rake

level and top up if required.

SWD030

Inclusive Roundabout
Maintenance Instructions
Sheet 6 of 6 Rev 01

NOTE

The warranty is invalidated if these instructions are not followed.

Summary of Contents for SWD030







Reviews: