background image

10

Step 3.  Install the Inside Antenna 

Inside antennas come in right angle antenna and flat panel versions. 

Installing Your Hardware

Note:

  

As you can see from the table above, acquiring the recommended inside and outside antenna separation optimizes coverage significantly. 
Any reduced antenna separation reduces the booster’s coverage.

Installing the SC-230W Yagi Antenna:

Step 1: Install U-Bolt on pole
Step 2: Slide pipe clamp over U-Bolt with the flat side facing away from the pipe.
Step 3: Slide antenna bracket onto U-Bolt in desired location.
Step 4: Install flat washer, split washer and nut, hand tighten
Note: Antenna may be installed on a variety of pipe angles, insure that the antenna is pointing in the direction 
of the closest cellular tower and is vertical with the drip hole at the bottom. To find the location of the closest 
cell tower go to: www.cellreception.com. 

Required Between 
Outside and Inside Antenna

antenna separation

If Coverage Area is … And Antenna Separa-

tion is…

Set all Dials to…

1500 - 2,000 

square feet

40-60 feet

Maximum Power

1,000 - 1,500 

square feet

30-40 feet

55 or 60

1,000 square feet 

and below

20-30 feet

45 or 50

SureCall | 48346 Milmont Drive, Fremont CA 94538 | 1-888-365-6283 | [email protected]

10

Summary of Contents for Fusion4Home Omni/Panel





















Reviews: