SureCall Force3 PSB User Manual Download | Manualshive

Page: 14 / 23

background image

SureCall | 48346 Milmont Drive, Fremont CA 94538 | 1-888-365-6283 | [email protected]

14

Installation

WARNING: FAILURE TO EXERCISE CAUTION WHEN
WORKING IN HIGH AREAS COULD CAUSE A FALL
AND PERSONAL INJURY.

CAUTION: AVOID AIMING A YAGI ANTENNA TOWARD
ANY INTERIOR ANTENNA.

1. Mount the antenna.
2. Connect a length of cable to the antenna and tighten until hand-tight.
3. Run the cable along the planned route.
4. Install a properly grounded SC-LP lightning protector.
5. Seal any holes you make in the outside of the building with appropriate caulking or sealant.

WARNING: DO NOT TOUCH ANY LIVE ELECTRICAL

WIRES OR ALLOW THE ANTENNA OR CABLING TO

TOUCH ANY LIVE ELECTRICAL WIRES.

«
...
12
13
14
15
16
...
»

Summary of Contents for Force3 PSB
























Reviews:

No comments

Related manuals for Force3 PSB

Brand: i3 International Pages: 2

Brand: i3 International Pages: 2

Brand: i3 International Pages: 22

Brand: Wavetronix Pages: 4

Brand: wavestore Pages: 11

Brand: X-10 Pages: 32

Brand: NAPCO Pages: 80

Brand: Arcteq Pages: 122

Brand: Speco Pages: 2

Brand: Titan Pages: 3

Brand: dallmeier Pages: 104

Brand: Velleman Pages: 4

Brand: R&D Pages: 4

Brand: Buckingham Pages: 2

Brand: Y-cam Pages: 88

Brand: 3xLogic Pages: 103

Brand: Visonic Pages: 6

Brand: Fracarro Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands