7.1. Faucet installation
NOTE: To seal the threaded connections, use teflon tape during the
installation. This doesn't apply to threads for plastic and faucet
nuts.
1) To install the faucet (fig.) drill two 12 mm holes in the countertop or
the sink (in case of enamelled sinks, the manufacturers
recommend drilling the holes in the support structure of the sink).
The holes should be 18 mm apart.
2) Put the metal washer 2 and the rubber seal 3 on the threaded
faucet connectors.
3) Mount the faucet in the previously drilled holes.
4) From the underside of the countertop, put washers 4, 5 on the
connectors, and tighten with nuts 7.
5) The water tubing needs to be connected to the faucet. To do this,
put metal nuts (9) and plastic clamps (8) on the tubing, and push
inserts (7) into the tubing.
6) Push the tubing (all the way) inside the faucet connectors and hand
tighten them with the nuts placed earlier on the tubing.
9. Filtration Cartridges
Dimensions
S-L-CARB
Coconut shell carbon filter cartridge. Improves taste and smell of water.
S-L-MIN
Water mineralizing cartridg enriches water with elements that are necessary for human body,
such as: calcium, magnesium, potassium and sodium.
9 7/8” x 2 1/2”
(25 cm x 6,5 cm)
9 7/8” x 2 1/2”
(25 cm x 6,5 cm)
9 7/8” x 2 1/2”
(25 cm x 6,5 cm)
10,8” x 2”
(27,5 cm x 5 cm)
Cartridge Type
Description / Filtration Stage
Longevity*
3 - 6 months
3 - 6 months
3 - 6 months
6 - 12 months
6 - 12 months
6 - 12 months
* Depends on amounts of filtered water, its quality and level of contamination.
Before the first use of system and after each cartridge replacement, the
system should be flushed with water for at least 5 minutes. Next, allow
the system to standby for 5-6 hours to activate its filtration ability. After
these procedures, filtered and conditioned water may be consumed.
WARNING! Filter cartridges are not subject to complaint at the
time of:
- after opening protective packaging,
- after first use of filter cartridges.
ATTENTION! Before first time use and each time after replacing RO
membranes element, proceed with backwash procedure.
Wait 60 minutes till water tank is full with water, next open system's content
faucet and drain entire water from the tank.
ATTENTION! Do not drink this water.
After this process is completed, leave the system idle for 5 to 6 hours to
activate filtration readiness. Next fill system's tank with newly filtered
water one more time and again open system's faucet and drain entire
water from the tank. ATTENTION! Do not drink this water.
S-PP20
Sediment filter for cold water. Used to filter potable and utility water - stops sand, rust particles,
suspended solids and contaminants contained in water with grain size of 20 microns and more. A
polypropylene spun cartridge improves organoleptic parameters of water.
S-PP5
Sediment filter for cold water. Used to filter potable and utility water - stops sand, rust particles,
suspended solids and contaminants contained in water with grain size of 5 microns and more. A
polypropylene spun cartridge improves organoleptic parameters of water.
S-BL
Fertilizing cartridge. Contains the sitered carbon with high absorptive abilities of chlorine and organic
substances contained in water. The sintered carbon has a large active surface and high efficiency of water
filtration.
AIFIR2000
2” Ionizer
AIFIR2000
regulates body's pH factor and helps to detoxify body (ionized water is an
excellent detoxifying agent).
Reverse osmosis membrane element removes 96% - 99% of all contaminants (including bacteria and
viruses).
up to
60 months
10” x 2”
(25 cm x 5,08 cm)
10” x 2”
(25 cm x 5,08 cm)
11,9” x 1,8”
(30 cm x 4,5 cm)
System backwash
supreme
best water solutions
3
4
5
6
7
8
9
12
18
