Supero SuperServer 5017R-MF User Manual Download

Page: 99 / 106

Appendix B: UEFI BIOS Recovery

B-1

Appendix B

UEFI BIOS Recovery Instructions

Warning!

Do not upgrade the BIOS unless your system has a BIOS-related

issue. Flashing the wrong BIOS can cause irreparable damage to the

system. In no event shall Supermicro be liable for direct, indirect, special,

incidental, or consequential damages arising from a BIOS update. If you

need to update the BIOS, do not shut down or reset the system while the

BIOS is updating to avoid possible boot failure.

B-1 An Overview to the UEFI BIOS

The Unifi ed Extensible Firmware Interface (UEFI) specifi cation provides a software-

based interface between the operating system and the platform fi rmware in the

pre-boot environment. The UEFI specifi cation supports an architecture-independent

mechanism for add-on card initialization to allow the UEFI OS loader, which is stored

in the add-on card, to boot up the system. UEFI offers a clean, hand-off control to

a computer system at bootup.

B-2 Recovering the UEFI Main BIOS Block

An AMIBIOS fl ash chip consists of a boot sector block and a main BIOS code block

(a main BIOS image). The boot sector block contains critical BIOS codes, including

memory detection and recovery codes for the user to fl ash a new BIOS image if the

original BIOS image is corrupted. When the system power is on, the boot sector

codes execute fi rst. Once it is completed, the main BIOS code will continue with

system initialization and bootup.

Note:

Follow the BIOS Recovery instructions below for BIOS recovery when the

main BIOS block crashes. However, when the BIOS Boot sector crashes, you will

need to send the motherboard back to Supermicro for RMA repair.

B-3 Recovery Using a USB-Attached Device

This feature allows the user to recover a BIOS image using a USB-attached device

without additional utilities used. A USB fl ash device such as a USB Flash Drive, or

a USB CD/DVD ROM/RW device can be used for this purpose. However, a USB

Hard Disk drive cannot be used for BIOS recovery at this time.

To perform UEFI BIOS recovery using a USB-attached device, follow the instruc-

tions below.

Summary of Contents for SuperServer 5017R-MF











































































































Search results

Summary of Contents for SuperServer 5017R-MF

Reviews:

Related manuals for SuperServer 5017R-MF

Brands by name

Popular brands

Supero SuperServer 5017R-MF, User Manual

Search results

Summary of Contents for SuperServer 5017R-MF

Reviews:

Related manuals for SuperServer 5017R-MF

Brands by name

Popular brands