Supero SUPERSERVER 1018D-73MTF User Manual Download

Page: 101 / 124

Chapter 7: BIOS

7-17



PCIe/PCI/PnP Confi guration

This feature allows the user to set the PCI/PnP confi gurations for the following items:

Above 4G Decoding

Select Enabled for 64-bit devices to be decoded above the 4GB address space

If 64bit PCI decoding is supported by the system. The options are

Disabled

and

Enabled.

VGA Palette Snoop

Select Enabled to support VGA palette register snooping which will allow the

PCI cards that do not contain their own VGA color palette to examine the video

cards palette and mimic it for proper color display. The options are

Disabled

and

Enabled.

PERR# Generation

Select Enabled to allow a PCI device to generate a PERR number for a PCI Bus

Signal Error Event. The options are

Disabled

and Enabled.

SERR# Generation

Select Enabled to allow a PCI device to generate an SERR number for a PCI Bus

Signal Error Event. The options are

Enabled

and Disabled.

Slot 1 PCI 33MHz OPROM/Slot 2 PCI 33MHz OPROM

Use this feature to enable or disable PCI slot Option ROMs. This is to boot the

computer using a device installed on the slot specifi ed. The options are Disabled,

Legacy

and EFI.

Launch Storage OPROM Policy

This feature controls how the system executes UEFI (Unifi ed Extensible Firmware

Interface), and legacy storage OPROM. Select Legacy Only to boot the system using

a legacy device installed in a PCI slot. The options are UEFI Only and

Legacy Only

Other PCI Device ROM Priority

This feature selects a PCI device OPROM to launch for system boot if this device

is not a network, mass storage, or video device. The options are UEFI Only and

Legacy Only

Summary of Contents for SUPERSERVER 1018D-73MTF





























































































































Search results

Summary of Contents for SUPERSERVER 1018D-73MTF

Reviews:

Related manuals for SUPERSERVER 1018D-73MTF

Brands by name

Popular brands

Supero SUPERSERVER 1018D-73MTF, User Manual

Search results

Summary of Contents for SUPERSERVER 1018D-73MTF

Reviews:

Related manuals for SUPERSERVER 1018D-73MTF

Brands by name

Popular brands