Supero SC819 Series User Manual Download Page 11

Page: 11 / 80

1-3

Chapter 1: Introduction

1-4 Contacting Supermicro

Headquarters

Address:

Super Micro Computer, Inc.
980 Rock Ave.
San Jose, CA 95131 U.S.A.

Tel:

+1 (408) 503-8000

Fax:

+1 (408) 503-8008

Email:

[email protected] (General Information)
[email protected] (Technical Support)

Web Site:

www.supermicro.com

Europe

Address:

Super Micro Computer B.V.
Het Sterrenbeeld 28, 5215 ML
's-Hertogenbosch, The Netherlands

Tel:

+31 (0) 73-6400390

Fax:

+31 (0) 73-6416525

Email:

[email protected] (General Information)
[email protected] (Technical Support)
[email protected] (Customer Support)

Asia-Pacific

Address:

Super Micro Computer, Inc.
3F, No. 150, Jian 1st Rd.
Zhonghe Dist., New Taipei City 23511
Taiwan (R.O.C)

Tel:

+886-(2) 8226-3990

Fax:

+886-(2) 8226-3992

Web Site:

www.supermicro.com.tw

Technical Support:
Email:

[email protected]

Tel:

+886-(2)-8226-3990

Summary of Contents for SC819 Series

















































































Search results

Summary of Contents for SC819 Series

Reviews:

Related manuals for SC819 Series

Brands by name

Popular brands

Supero SC819 Series, User Manual

Search results

Summary of Contents for SC819 Series

Reviews:

Related manuals for SC819 Series

Brands by name

Popular brands