Chapter 2: Installation
2-29
BIOS Recovery
The BIOS Recovery jumper (JBR1) is a
slide switch that is used to enable or
disable the BIOS Recovery feature of the
motherboard. See Appendix D for details.
BIOS Recovery
Switch Settings
State Definition
Pins 1-2
Normal (Default)
Pins 2-3
BIOS Recovery
Watch Dog
Jumper Settings
Jumper Setting Definition
Pins 1-2
Reset (default)
Pins 2-3
NMI
Open
Disabled
Watch Dog Timer
Watch Dog (JWD1) is a system monitor
that can reboot the system when a soft-
ware application hangs. Close pins 1-2 to
reset the system if an application hangs.
Close Pins 2-3 to generate a non-maskable
interrupt signal for the application that
hangs. Refer to the table on the right for
jumper settings.
COM1
RST
PWR
ON
OH/FF
X
NIC
1
HDD
LED
PWR
LED
JF1
TPM/PORT80
JTPM1:
JTPM1
JL1
TH1
USB 12/13(3.0)
JSTBY1
USB 4/5
USB 2/3
JBR1
LED BOOT
LED VGA
LED DIMM
CPU
LED
AUDIO FP
LED1
1-2:RST
2-3:NMI
JWD1:
JL1:
CHASSIS
INTRUSION
THERMAL SENSOR
TH1:
2-3:BIOS RECOVERY 1-2:NORMAL
J9701
J9702
JI2C1
JI2C2
WATCH DOG
5V STBY POWER
JSTBY1:
JBR1
OC1
OFF:DISABLE
JI2C1/JI2C2
ON :ENABLE
LED4
JWD1
PCH SLOT1 PCI-E 3.0 X4
2-3:DEBUG MODE
J9701/J9702
1-2:NORMAL
RESET
PCIE M.2 CONNECTOR 2
2260
1-2:NORMAL
2-3:ME MANUFACTURING MODE
JPME2:
2280
22110
CLEAR
BUTTON
SPEAKER:Pin1-4
JD1:
CMOS JSD1:SATA DOM PWR
POWER
PCH SLOT2 PCI-E 3.0 x1
PCH SLOT1 PCI-E 3.0 x4
JPME2
CPU SLOT3 PCI-E 3.0 x8 (IN x16)
JSD1
BUTTON
JD1
JBT1
JBT1:CMOS CLEAR
I-SATA4
I-SATA5
PCH SLOT4 PCI-E 3.0 x1
I-SATA2
I-SATA3
JSPDIF_OUT
PCH SLOT5 PCI-E 3.0 x1
I-SATA1
I-SATA0
CPU SLOT6 PCI-E 3.0 x16
PCIE M.2 CONNECTOR 1
SYS_FAN3
SYS_FAN2
HD AUDIO
2260
2280
22110
CPU
USB 6/7/8/9(3.0)
DVI
JPW1
JPUSB1:USB0/1 WAKE UP
HDMI/DP
2-3 DISABLE
1-2 ENABLE
DIMMB2
DIMMA2
DIMMB1
DIMMA1
CPU_FAN2
CPU_FAN1
JVR1
SYS_FAN1
JPW2
JPUSB1
KB/MOUSE USB 0/1
LED10
LED9
LED8
LED7
LED6
DESIGNED IN USA
REV:1.00
C7Z370-CG
-L
BIOS LICENSE
MAC CODE
BAR CODE
+
A
C
A
A
A
A
C
C
C
C
USB 10(3.1)
LAN
USB 11(3.1)
X
LED5
C
A
A
C
A. Watch Dog Timer
B. J9702
C. J9701
D. BIOS Recovery
B
A
Manufacturing Mode (VRM
Programming)
J9701 and J9702 are VRM programming
jumpers used for updating the CPU VRM
code. See the table on the right for
jumper settings.
VRM Programming
Switch Settings
State Definition
Pins 1-2
Normal
Pins 2-3
Debug Mode
C
D
