Supermicro X5DE8-GG User Manual Download Page 7

Page: 7 / 90

Chapter 1: Introduction

1-1

Introduction

Chapter 1

Introduction

1-1

Overview

Checklist

Congratulations on purchasing your computer motherboard from an ac-

knowledged leader in the industry. Supermicro boards are designed with

the utmost attention to detail to provide you with the highest standards in

quality and performance.

Please check that the following items have been included with your mother-

board. If anything listed here is damaged or missing, contact your retailer.

One (1) Supermicro Mainboard

One (1) ribbon cable for IDE devices

One (1) floppy ribbon cable

One (1) USB cable

One (1) COM port (serial) cable

One (1) I/O backpanel shield

One (1) Supermicro CD or diskettes containing drivers and utilities

One (1) User's/BIOS Manual

Two (2) Pentium 4 Xeon active heatsinks (FAN-042, retail only)

Two (2) heatsink retention clip kits (SKT-095-604)

SCSI Accessories (X5DE8-GG only)

One (1) 68-pin LVD Ultra320/160 SCSI cable

One (1) set of SCSI driver diskettes

One (1) SCSI manual

Summary of Contents for X5DE8-GG



























































































Search results

Summary of Contents for X5DE8-GG

Reviews:

Related manuals for X5DE8-GG

Brands by name

Popular brands

Supermicro X5DE8-GG, User Manual

Search results

Summary of Contents for X5DE8-GG

Reviews:

Related manuals for X5DE8-GG

Brands by name

Popular brands