Supermicro X5DE8-GG User Manual Download Page 68

Page: 68 / 90

4-16

UPER X5DE8-GG/X5DEI-GG/X5DEE-M

User’s Manual

Hyper-threading

Enables hyper-threading if supported by the operating system. Hyper-

threading is a method of creating an additional "virtual" processor by using

parallelism to process mulitple instructions simultaneously. The settings for

this option are

Enabled

and Disabled.

Watchdog Timer

This option is used to configure the Watchdog timer. Settings are

Dis-

abled

, 2 minutes, 5 minutes, 10 minutes and 15 minutes.

Auto DQS Setting Support

The settings for this option are

Disabled

and Enabled.

DQS Selection

This setting is preset.

Spread Spectrum

Spread Spectrum is a technique used to stabilize a system that is being

affected by electromagnetic interference. The settings for this option are

Disabled

and Enabled.

Memory Enhance Mapping

The settings for this option are

Enabled

and Disabled.

Summary of Contents for X5DE8-GG



























































































Search results

Summary of Contents for X5DE8-GG

Reviews:

Brands by name

Popular brands

Supermicro X5DE8-GG, User Manual

Search results

Summary of Contents for X5DE8-GG

Reviews:

Brands by name

Popular brands