Supermicro X5DE8-GG User Manual Download Page 15

Page: 15 / 90

Chapter 1: Introduction

1-9

Introduction

X5DEI-GG/X5DEE-M* Quick Reference

Jumper

Description

Default

Setting

JBT1

CMOS Clear

See Chapter 2

JF2

Speaker Enable (page 2-12)

Close 6-7 (Enabled)

JP1

VGA Enable/Disable

Pins 1-2 (Enabled)

JP2

Watch Dog Enable/Disable

Open (Disabled)

JP3

System (Front Side) Bus Speed Pins 1-2 (Auto MHz)

JP4

OH/Chassis Fan Select

Open (OH Fan)

JPL1*

LAN1 Enable/Disable

Pins 1-2 (Enabled)

JPL2*

LAN2 Enable/Disable

Pins 1-2 (Enabled)

Switch

Description

DIP Switch 1

Processor Speed

Connector

Description

ATX PWR CONN

Primary ATX Power Connector

COM1/COM2

COM1/COM2 Serial Port Connector

CPU/CHS/OH FAN

CPU/Chassis/Overheat Fan Headers

DIMM1-DIMM4

Memory (RAM) Slots

GLAN1/2*

G-bit Ethernet Ports 1and 2

IPMI

IPMI 1.5 Slot (for daughter card)

Processor Power Connector

Third Power Supply Fail Header

Parallel (Printer) Port

J10

Chassis Intrusion Header

J11

PS/2 Keyboard/Mouse Ports

J12

Floppy Disk Drive Connector

J18/19

IDE1/2 Hard Disk Drive Connector

JF1

Front Control Panel Connector

JF2

Speaker/PWR LED Headers

USB0/1

Universal Serial Bus Ports

USB2/3

Additional USB Headers

WOL

Wake-on-LAN Header

*The X5DEI-GG has two Gb Ethernet ports while the X5DEE-M has a single

10/100 Mb Ethernet port.

Summary of Contents for X5DE8-GG



























































































Search results

Summary of Contents for X5DE8-GG

Reviews:

Brands by name

Popular brands

Supermicro X5DE8-GG, User Manual

Search results

Summary of Contents for X5DE8-GG

Reviews:

Brands by name

Popular brands