manualshive.com logo in svg

Supermicro X5DE8-GG, User Manual

Share
Download
Supermicro X5DE8-GG User Manual Download Page 62

4-10

S

UPER X5DE8-GG/X5DEI-GG/X5DEE-M

 

User’s Manual

Floppy Configuration

Floppy A

Use this option to specify which of floppy drive you have installed in the A

drive.  The settings are Disabled, 360 KB 5 1/4", 1.2 MB 5 1/4", 720 KB 3 1/

2", 

1.44 MB 3

 

1/2"

 and 2.88 MB 3 1/2".

Floppy B

Use this option to specify which of floppy drive you have installed in the B

drive.  The settings are 

Disabled

, 360 KB 5 1/4", 1.2 MB 5 1/4", 720 KB 3

1/2", 1.44 MB 3

 

1/2" and 2.88 MB 3 1/2".

Floppy Drive Seek

Use this option to Enable or 

Disable

 the floppy seek routine on bootup.

Boot Settings Configuration

Quick Boot

This option allows the BIOS to skip certain tests that are normally perfomred

on boot up.  You can disable the option to speed up boot time.  The settings

are Disabled and 

Enabled

.

Quiet Boot

If Disabled, this option will cause the normal POST messages to be dis-

played upon setup.  When Enabled, the OEM logo is displayed instead of the

POST messages. The settings are 

Enabled

 and Disabled.

Add-On ROM Display Mode

Set this option to display add-on ROM (read-only memory) messages. The

settings for this option are 

Force BIOS

 and Keep Current.  Force BIOS

allows the computer to force a third party BIOS to display during system

boot.  Keep Current has the system display AMIBIOS information on bootup.

Summary of Contents for X5DE8-GG



























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands