Supermicro AS-1020P-8R User Manual Download Page 83

Page: 83 / 104

Chapter 7: BIOS

7-11

Palette Snooping

Select "Enabled" to inform the PCI devices that an ISA graphics device is installed

in the system in order for the graphics card to function properly. The options are

Enabled and

Disabled

PCI IDE BusMaster

Set this value to allow or prevent the use of PCI IDE busmastering. Select "Enabled"

to allow AMI BIOS to use PCI busmaster for reading and writing to IDE drives. The

options are

Disabled

and Enabled.

Offboard PCI/ISA IDE Card

This option allows the user to assign a PCI slot number to an Off-board PCI/ISA

IDE card in order for it to function properly. The options are

Auto

, PCI Slot1, PCI

Slot2, PCI Slot3, PCI Slot4, PCI Slot5, and PCI Slot6.

IRQ3/IRQ4/IRQ5/IRQ7/IRQ9/IRQ10/IRQ11/IRQ14/IRQ15

This feature speciﬁ es the availability of an IRQ to be used by a PCI/PnP device.

Select Reserved for the IRQ to be used by a Legacy ISA device. The options are

Available

and Reserved.

DMA Channel0/Channel1/Channel3/Channel5/Channel6/Channel7

Select Available to indicate that a speciﬁ c DMA channel is available to be used by

a PCI/PnP device. Select Reserved if the DMA channel speciﬁ ed is reserved for

a Legacy ISA device. The options are

Available

and Reserved.

Reserved Memory Size

This feature speciﬁ es the size of memory block to be reserved for Legacy ISA

devices. The options are

Disabled

, 16K, 32K and 64K.

Summary of Contents for AS-1020P-8R









































































































Search results

Summary of Contents for AS-1020P-8R

Reviews:

Related manuals for AS-1020P-8R

Brands by name

Popular brands

Supermicro AS-1020P-8R, User Manual

Search results

Summary of Contents for AS-1020P-8R

Reviews:

Related manuals for AS-1020P-8R

Brands by name

Popular brands