background image

Superior

 

PAPER HANDLING SOLUTIONS

 

 

8

 

 

© 2005-2015 Superior-PHS

 

3. 

Skip Flight:

  When running on a lugged/flighted conveyor you can add a Skip Count to 

miss desired lug pockets.  When set to “0”/zero the system will feed or drop into every 

pocket.  When set to 1 the system will feed/drop into the first pocket, then skip one 

pocket, then feed the next pocket and repeat sequence.  If Skip Flight is set to 2, then 

system will feed first pocket and skip the next 2, and etc.   Press the value/number 

button to bring up keypad.  Enter required value, press enter to save and return to Main 

Set-up Screen.   

4. 

Pause/Resume ON/OFF:

   Pause/Resume can operate in feeder only or with the 

dropper on. When Pause/Resume mode is turned ON, press the cycle button to start the 

first batch, then Feeder will automatically 

“Pause” at the end of the first batch for the 

preset amount of Pause Time, then Automatically Resume the next batch.  This creates 

a gap on the shingling conveyor notifying the operator where the batches begin and end.   

Press the ON/OFF button to toggle between ON and OFF.  The pause time can be set 

by using the pause/resume input ( #5 below ). 

5. 

Pause/Resume Time:

   When Pause/Resume mode is turned ON, sets amount of 

Pause time between end of a batch and the automatic starting of the next batch.  Press 

adjacent time button to bring up keypad.  Enter required Pause time, press enter to save 

and return to Main Set-up Screen. 

6. 

Up/Down Screen Arrow Buttons

:  When pressed moves to the next screen. 

7. 

Run Screen Button

:  Takes operator directly to Run Screen 

8. 

Dropper Screen Button:

   Takes operator directly to Dropper screen. 

Summary of Contents for Xtreme XM Series


















Reviews: