background image

Superior Performance, Superior Value 

 

© 2005-2013 Superior-PHS 

15 

DROPPER SCREEN 

batch.   When in the Manual Mode and Dropper is ON, system will not cycle as in Auto 

Mode.  System will ONLY allow operator to press Dropper Cycle Button.  See Section 5 

below. 

5. 

Dropper Cycle and Open/Close Button:

  When Dropper is ON and Dropper is in Manual 

Mode, this button will manually cycle the dropper forks one half of a cycle.  If the button is 

pressed when dropper forks are fully extended, forks will fully retract into the base.  If the 

button pressed with forks fully retracted into the base, forks will fully extend out.   If the 

button pressed with forks in between fully retracted and fully extended, dropper forks will 

fully retract into base.   This button will only activate the dropper forks and it will not activate 

the feeder. 

Note: This feature is active with the cover open if it’s in manual mode. 

6. 

Up/Down Screen Arrow Buttons

:  When pressed moves to the next or previous screen. 

7. 

Run Screen Button

:  Takes operator directly to Run Screen 

8. 

Dropper Screen Button:

   Takes operator directly to Dropper screen. 

 

NOTE: Dropper is programmed with a safety fault. If for any reason the forks while 

extending were to jam the feeder and dropper will reset to the retracted stage 

Summary of Contents for Xtreme XM Series


















Reviews: