background image

16

NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.

ACCESSORY COMPONENTS

Remote Control System (Standard)

H0249

RCL

Standard Remote Control System
(Model RCL)

The Model RCL (Standard) Remote Control
System, features a simplistic on/off control
function for the fireplace.  This model includes
a hand-held transmitter, a remote receiver
with wall-mount coverplate and all hardware
required to install the unit.  The remote re-
ceiver can be wall or hearth mounted.
The transmitter has ON and OFF functions that
are activated by pressing either button on the
face of the transmitter.  When a button on the
transmitter is pressed, a signal light illuminates
briefly to verify that a signal has been sent.
The Model RCL is designed to operate with all
millivolt ignition systems, as well as electronic
ignition systems.  It may be installed with use for
either natural or propane gas appliances.  The
RCL offers ease of installation and allows you to
execute on-off commands to the fireplace
effortlessly with one simple  motion.
The Model RCL comes complete with detailed
operating instructions.

Forced Air Kit

051331

FAB-1600

with Variable Speed Wall Switch

Forced Air Kit

If the optional forced air kit, Model FAB-1600,
is to be used on the GHC-6500 Series appli-
ances, refer to the installation instructions
packed with the fan kit. The GHC-6500 Series
appliances have been pre-wired at the factory
to accept the forced air kit at some later time.
The appliance, must however, be connected to
the main power supply at the time of installa-
tion if the FAB-1600 forced air kit is to be
installed later. The kit comes with a variable
speed wall switch.

Horizontal Trim Installation

There are two (2) optional horizontal trim kits,
Models 41HTK-PB, 41HTK-SPB available for
use with the GHC Series appliance. The 41
HTK-SPB kit's trim is solid polished brass, as
opposed to the 41HTK-PB kit's trim which has
a polished brass coating. Refer to the specific
installation instructions packed with each trim
kit for their proper usage and installation.

Horizontal Trim Kit

051251

41HTK-SPB

Horizontal Trim Kit

051252

41HTK-PB

Bi-Fold Doors

12M07

 38ABF

12M08

38ABF-BB

12M09

38ABF-BS

Aluminum-Framed Bi-Fold Doors

Your appliance can be fitted with beautiful
aluminum-framed bi-fold doors.  Model 38ABF
doors are available for use with these appli-
ances.  Doors are easily fitted to the fireplace
opening. Model 38ABF  doors come with stan-
dard black finish.  Model 38ABF-BB doors have
a beautiful brass finish.  Model 38ABF-BS doors
have a brushed stainless finish.

Aluminum-Framed Twin Pane Door

Your appliance can be fitted with beautiful
aluminum-framed twin pane doors. Models
38TBA-BB and 40TBA-BB doors are available
for use with these appliances.  Doors are easily
fitted to the fireplace opening. Both models
come with a beautiful bright brass finish.

Glass Enclosure Panels

Your appliance can be fitted with beautiful
glass enclosure panels.  Model 38AGEP and
40AGEP doors are available for use with these
appliances.  Doors are easily fitted to the fire-
place opening. Model 38AGEP and 40AGEP
doors come with a standard black finish. Model
38AGEP-BB and 40AGEP-BB doors come with
beautiful bright brass finish.

Twin Pane Door

12M45

40TBA-BB

Twin Pane Door

12M44

 38TBA-BB

Glass Enclosure Panels

12M51

38AGEP

12M52

38AGEP-BB

12M53

40AGEP

12M54

40AGEP-BB

To ensure warranty and to prevent a potential
fire hazard, do not use any other doors on
these appliances.

Summary of Contents for GHC-6500 SERIES



















Reviews: