background image

www.www.SuperiorFireplaces.US.com

126826-01A

5

PRODUCT IDENTIFICATION

Figure 1 - Product Identification

Control 

Knob

Base Assembly

Ignitor on 

the side

Rear Burner

LOCAL CODES

State of Massachusetts:

 The installa-

tion must be made by a licensed plumber 

or gas fitter in the Commonwealth of 

Massachusetts.
Sellers of unvented propane or natural 

gas-fired supplemental room heaters shall 

provide to each purchaser a copy of 527 

CMR 30 upon sale of the unit.
Vent-free gas products are prohibited for 

bedroom and bathroom installation in the 

Commonwealth of Massachusetts.

UNPACKING

 CAUTION: Do not remove the 

data plates from the grate as-

sembly. The data plates contain 

important warranty and safety 

information.

1.  Remove logs and heater base assembly 

from cartons. 

 

Note: Do not pick up heater base assem-

bly by burners. This could damage heater. 

Always handle base assembly by grate. 

2.  Remove all protective packaging applied 

to logs and heater for shipment.

3.  Check heater for any shipping damage. 

If heater is damaged call INNOVATIVE 

HEARTH PRODUCTS at 1-800-655-2008 

for replacement parts before returning to 

dealer.

Install and use heater with care. Follow all 

local codes. In the absence of local codes, 

use the latest edition of 

The National Fuel 

Gas Code, ANSI Z223.1/NFPA 54

*.

*Available from:

American National Standards Institute, Inc.

1430 Broadway

New York, NY 10018

National Fire Protection Association, Inc.

Batterymarch Park

Quincy, MA 02269

Left

Side

Right

Side

Front

Summary of Contents for BGE18NT













































Reviews: