background image

www.www.SuperiorFireplaces.US.com

126826-01A

19

INSTALLATION

Continued

3.  Place left ember bed log (18" D-073, 24" 

& 30" D-048) as shown in Figure 24. The 

log has groove on one side that sets on the 

ember bed pan. The back side of this log 

needs to rest against the front of the base 

assembly. Make sure the flame from the 

ember pan does not touch the ember bed 

log.

Figure 24 - Installing Left Ember Bed Log

Left Ember 

Bed Log

Figure 26 - Installing Left Middle Log

Left Middle 

Log

Figure 25 - Installing Right Ember Bed Log

Right Ember 

Bed Log

Hole 

Underneath

Grate Prong

4.  The  right  ember  bed  log  24"  &  30''  (D-

047) has a hole in the log that sets on 

the grate finger and the other end rest on 

the fireplace floor, place log as shown in 

Figure 25. The right ember bed logs for 18" 

(D-072) has a groove on the side that sets 

on the ember bed pan and the back of the 

log needs to rest against the front of the 

base. Make sure the flame from the ember 

pan does not touch the ember bed log. The 

back side of this log needs to rest against 

the front of the base assembly, make sure 

the flame from the ember pan does not 

touch the ember bed log.

5.  The left middle log (18" D-066, 24" & 30" 

D-040) has a groove on the bottom to sit 

on the chassis and has to sit on the tab on 

the back of the left front log as shown in 

Figure 26.

6.  The right middle log (18" D-067, 24" & 30" 

D-041) has a groove on the bottom to sit on 

the chassis and has to sit on the tab on the 

back of the right front. The right middle log 

should have a recess area that fits around 

the ramp log as shown in Figure 27.

Figure 27 - Installing Right Middle Log

Right Middle 

Log

Summary of Contents for BGE18NT













































Reviews: