background image

SuperiorFireplaces.us.com

127055-01_H

8

VENTING INSTALLATION

  

Continued

Figure 7 - Typical Offset Terminations

Figure 8 - Ceiling Support Pipe  12S-8DM

USING ELBOW OFFSETS 30E-12DMO-8DMR

To clear overhead obstructions, you may offset your chimney system 

using 30E-12DMO-8DMR 30° Offset/return elbow.
A section or sections of chimney may be used between offsets and 

return elbow. Transition pipe must be used after elbow offset is at-

tached.
1.  To achieve desired offset, you may install combinations of 12", 

18", 24", 36" and 48" length of double wall pipe (see offset chart, 

page 9 and Figure 7).

 

Note:

 For systems with 2 elbow sets, minimum height is 22 feet. 

Maximum height for any system is 50 feet.

2.  Chimney weight above offset rests on return elbow. Straps must 

be securely nailed to rafters or joists (see Figure 8, details A and 

B).

3.  Maximum length of pipe between supports (return elbow or 12S-

8DM) is 6' of angle run. Maximum of two 6' angle run sections 

per chimney system (see Figure 7).

4.  All pipe connections between offset and return must be secured 

with two screws on outer pipe only (see Figure 9, page 9). Do not 

penetrate inner stainless.

2" (51 mm)

Min.

Straps

Straps

Straps

Straps

Detail A Return Elbow

Detail B Angle Firestop

See Detail A

See Detail B

Ceiling Support 

Pipe 12S-8DM

30E-8DM

Return Elbow

30E-8DM

Return Elbow

30E-8DM 

Offset Elbow

30E-8DM 

Offset Elbow

30E-12DMO-8DMR 

Offset Elbow

30E-12DMO-8DMR 

Offset Elbow

30E-12DMO-

8DMR Offset 

Elbow

30E-12DMO-8DMR 

Return Elbow

30E-12DMO-8DMR 

Return Elbow

30E-12DMO-

8DMR Return 

Elbow

Starter Section

Starter Section

Starter Section

8 DM Pipe

8 DM Pipe

Ceiling 

Support Pipe 

12S-8DM

A

B

C

6' Max. (1.83 m)

6' Max. (1.83 m)

6' Max. (1.83 m)

6' Max. (1.83 m)

6' Max. (1.83 m)

6' Max. (1.83 m)

Summary of Contents for WRE3042WH

























Reviews: