background image

SuperiorFireplaces.us.com

127055-01_H

11

Figure 15 - Termination

Attach Bracket Tabs to 

Outer Pipe (3 Places) 

Secure with Screws

RLT-8DM

Level of Flue 

Gas Outlet

Caulk

Collar

Flashing

Underlap Shingles 

Bottom Only

Overlap Shingles 

Top and Sides

Figure 16 - Multiple Chase Installation

CHASE INSTALLATIONS

Instructions for chase installations are included with the chase style 

termination chosen. In a multiple chase installation, be sure to provide 

adequate distance between terminations to prevent smoke spillage 

from one termination to another. We suggest that terminations be 

separated at least 24", center to center and stacked at a vertical height 

difference of 18" (see Figure 16).

Note: 

If a decorative shroud is to be installed, contact the manufac-

turer for specifications.

10 FOOT RULE

All flue gas outlet chimney terminations must extend a minimum of 

3 feet in height above the highest point where it passes through the 

roof and must be at least 2 feet above the highest point of the roof 

that is within a horizontal distance of 10 feet (see Figure 17).

FINISHING FIREPLACE

Combustible materials, such as wallboard, sheet rock, drywall, ply-

wood, etc. may make direct contact with sides and top around the 

fireplace face. It is important that combustible materials do not overlap 

the face itself. Brick, glass, tile or other noncombustible materials 

may overlap the front face provided they do not obstruct essential 

openings like louvered slots or any other opening. When overlapping 

with a noncombustible facing material, use only noncombustible 

mortar or adhesive.

VENTING INSTALLATION

  

Continued

Figure 17 - 10 Foot Rule

Figure 18 - Typical Residential Installations

10

'

(3.05 m) 

10

'

(3.05 m) 

2

(0.61 m)

Min.

2

(0.61 m) Min.

3

(0.92 m)

Min.

3

(0.92 m)

Min.

Level of 

Flue Gas Outlet 

24" (610 mm)Min.

24" (610 mm)Min.

18" 

(458 mm)

Min. Typ.

30E-12DMO-8DMR

30E-12DMO-8DMR

30E-12DMO-8DMR

EFFECTIVE HEIGHT 

OF TERMINATION CAP

EFFECTIVE HEIGHT 

OF TERMINATION CAP

EFFECTIVE HEIGHT 

OF TERMINATION CAP

EFFECTIVE HEIGHT 

OF TERMINATION CAP

14 

1

/

2

  

FT.

(4.42 M)

MINIMUM

HEIGHT

14 

1

/

2

  

FT.

(4.42 M)

MINIMUM

HEIGHT

MAX. HEIGHT

50 FT. (15.24 M)

ANY SYSTEM

MIN. HEIGHT OF

22 FT. (6.71 M)

WITH 2

ELBOW SETS

MAX. HEIGHT OF

50 FT. (15.24 M)

UP TO 

6FT. 

(1.83 M)

MAX.

UP TO 

6FT. 

(1.83 M)

MAX.

STARTER

SECTION

STARTER

SECTION

STARTER

SECTION

Summary of Contents for WRE3042WH

























Reviews: