Superior Fireplaces WCT6840WS Installation And Operation Instructions Manual Download | Manualshive

Page: 8 / 26

background image

Marginal Location

Wind Direction

Location

Not

Recommended

Outside Air Intake

Facing the Wind

Location

Not

Recommended

Location Recommended

Figure 8

When selecting the location, the chimney outlet position and the direction of the wind are important factor affecting the chimney performance. To

allow a maximum draft and to reduce wind turbulence, the chimney must:

• Penetrate the highest part of the roof.

• Be installed as far as possible of roof offsets, trees or any other obstructions that may cause wind turbulence and back drafts in the chimney.

• The least amount of offsets (elbows) possible.

NOTE: A maximum of 2 offsets is allowed.

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

8

«
...
6
7
8
9
10
...
»

Summary of Contents for WCT6840WS



























Reviews:

No comments

Related manuals for WCT6840WS

Brand: Superior Pages: 12

Brand: GDC Pages: 5

Brand: Comfort Glow Pages: 20

Brand: Safire Pages: 17

Brand: Quality Craft Pages: 7

Leveling Leg Field Fix Kit MPE-27

Brand: Lennox Hearth Products Pages: 1

SHEFFIELD FA146S

Brand: pleasant hearth Pages: 6

Brand: Isokern Pages: 16

Brand: Valor Pages: 43

Brand: Warm Tech Pages: 24

Brand: Twin-Star International Pages: 15

MAJESTIC ODGSR36ANAU

Brand: Raypak Pages: 20

Brand: Ravelli Pages: 100

Brand: Paragon Pages: 32

Brand: Grand Canyon Gas Logs Pages: 10

Brand: Heat & Glo Pages: 65

Brand: Quadra-Fire Pages: 64

Brand: Twin-Star International Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands