Superior Fireplaces WCT6840WS Installation And Operation Instructions Manual Download

Page: 11 / 26

Figure 11

Insulated Chase Construction

7 Ft.

Min.

Attic

Radiation

Shield

Roof Support

Storm

Collar

Flashing

Drywall or

Any Rigid

Material

2” x 4”

1/2” Plywood

6’ 8”

Min.

Firestop

* Floor

Ceiling

Wall

* Floor

Ceiling

Wall

Fireplace

Insulate Joists

Same As Ceiling

Draft Stops

Firestop

CTDT

Termination

Note: Non-

Combustible

Chase

Flashing

Must Be

Used To

Cover

Chase

Opening

Optional

Insulation

In Outside

Walls Of

Chase

Solid

Continuous

Surface

Outside

Base

Insulation

(Thermal Barrier)

Level

NOTE: It is recommend-

ed that the chase walls

and floor be insulated in

the same manner, using

the same insulation, as

the rest of the building,

below the attic.

• Must have the same firestopping

resistance as adjacent wall.

• Must have the same insulation as

adjacent ceiling.

• Follow local rules regarding fram

ing construction.

1. Fireplace

2. Front of fireplace

3. Wood frame (2” x 3” min)

4. Drywall

5. Tiles

6. Rock board or other

7. Brick

Fireplace Frame Section

(Top View)

Figure 12

Only non-combustible material

should be superposed or project-

ing over the front of the fireplace.

Figure 14

50”

Min.

SEE NOTE

MANTEL and FACING

The mantel must be installed at least 56”

(1143 mm) above the base of the fireplace

(Figure 13)

Nailing Flanges

Four nailing flanges are provided to secure the

fireplace to the floor (see figure below). Bend

the nailing flanges down so that each flange is

flush with the floor, then using nails or screws,

secure the fireplace to the floor (2 places each

side). The heads of the screws or nails must

be large enough to completely cover the holes

in the nailing flanges.

Nailing Flange

(2 places each side)

Unbend to floor

and nail/screw

Fireplace Side

7 Ft.

Min.

Attic

Radiation

Shield

Roof Support

Storm

Collar

Flashing

Drywall or

Any Rigid

Material

2” x 4”

1/2” Plywood

6’ 8”

Min.

Firestop

* Floor

Ceiling

Wall

* Floor

Ceiling

Wall

Fireplace

Figure 13

...............

..........

Mantel

Noncombus-

tible Facing

56”

Drywall

2” X 3” Min.

Spacer

Mantel and Facing

(Side View)

...............

..........

Rock Board or Other

Noncombustible

Material

Noncombustible

Facing

Drywall

Rock Board or

Other Noncom-

bustible Material

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

Summary of Contents for WCT6840WS



























Search results

Summary of Contents for WCT6840WS

Reviews:

Related manuals for WCT6840WS

Brands by name

Popular brands

Superior Fireplaces WCT6840WS, Installation And Operation Instructions Manual

Search results

Summary of Contents for WCT6840WS

Reviews:

Related manuals for WCT6840WS

Brands by name

Popular brands