background image

SuperiorFireplaces.us.com

900467-01B

7

INSTALLATION

Continued

INSTALLING DAMPER CLAMP ACCESSORY FOR 

VENTED OPERATION

NOTE

: When used as a vented indoor appliance, appliance 

must be installed only in a solid-fuel burning fireplace with 

a working flue and constructed of noncombustible material.

For Massachusetts Residents Only:

 Installation of this gas 

log set as a vented indoor appliance in the Commonwealth of 

Massachusetts requires the damper be permanently removed 

or welded in the fully open position.
You must install the damper clamp accessory 

(to order, see 

Accessories, 

Page 23

).

 This will ensure vented operation 

(see 

Figure 8

)

. The damper clamp will keep damper open. 

Installation instructions are included with clamp accessory.

See chart below for minimum permanent flue opening you 

must provide. Attach damper clamp so the minimum perma-

nent flue opening will be maintained at all times.

Area of Various Standard Round Flues

 

Diameter

 

Minimum Required Area

 

5" 

20 sq. inches

 

6" 

29 sq. inches

 

7" 

39 sq. inches

 

8" 

51 sq. inches

Figure 8 - Attaching Damper Clamp

Damper

Damper 

Clamp

Damper

Damper 

Clamp

Damper

Manufactured Fireplace

Masonry Fireplace

INSTALLING APPLIANCE BASE ASSEMBLY

 

WARNING: You must secure this appliance 

to fireplace floor. If not, appliance will move 

when you adjust controls. Moving appliance 

may cause a gas leak.

 

WARNING: If installing in a sunken fireplace, 

special care is needed. You must raise the fire

-

place floor to allow access to appliance control 

panel. This will ensure adequate air flow and 

guard against sooting and controls being dam-

aged. Raise fireplace floor with noncombustible 

material. Make sure material is secure.

Installation Items Needed

•  hardware package (provided with appliance)

•  approved flexible gas hose and fittings  provided (if allowed 

by local codes) 

•  sealant (resistant to propane/LP gas, not provided)
•  electric drill with 3/16” masonry drill bit

NOTE

: Install optional MRC Series receiver and hand-held 

remote control kit (see 

Accessories, 

Page 23

) before install

-

ing gas log appliance. See installation instructions included 

with the kit. 

1.  Apply pipe joint sealant lightly to male threads of the 1/2 NPT 

side of gas fitting elbow (provided) and connect to inlet side 

of gas control. Remove gas fitting from flexible gas hose 

(provided) before connecting to elbow 

(see 

Figure 9

)

2.  Position appliance base assembly in fireplace. 

3.  Mark screw locations through holes in front panel of base 

(see 

Figure 10, Page 8

)

. If installing in a brick-bottom 

fireplace, mark screw locations in mortar joint of bricks.

4.  Remove appliance base from fireplace.

5.  Drill holes at marked locations using 3/16" drill bit. 
6.  Attach base, through holes in back side panels of base, to 

fireplace floor using masonry screws provided in hardware 

package 

(see 

Figure 10, Page 8

)

.

7.  Connect to gas supply. See 

Connecting To Gas Supply

.

Figure 9 - Attaching Flexible Gas Hose to Appliance 

Gas Regulator

  

Gas Control 

Flexible Gas Hose 

(Provided with VGC 

Series Models Only)

 (Install if allowed by 

local codes) 

Elbow, 1/2 NPT x 

3/8 Flare

WARNING: DO NOT INSTALL IN 

SLEEPING ROOM OF MOBILE HOMES.

    Chimney  Height          Minimum Permanent Flue Opening

    6' to 15'                   39 sq. inches
    15' to 30'                  29 sq. inches

f i r e - p a r t s . c o m

Summary of Contents for LMF30GT































Reviews: