Important: Read all instructions prior to installation.
DMX Master/Decoder for LED DMX Controllers
with Digital Address Display - 1 Channel, 10A
One channel DMX Controller/Decoder controls a single LED product
such as a light bar or strip. The DMX base address is easily set using
push button switches under the display. DMX-512 digital control signals
are received via 3 wire terminal strip connection. DMX decoding driver
converts universal DMX512/1990 digital signal to PWM signal, which
can be controlled by DMX512 console. 4096 grey scales are available
when used in master mode. Maximum load 10 Amps available DMX
Starting Channels 001-512.
Instructional Sheet
Part Number:
4400 Earth City Expy, St. Louis MO 63045
866-590-3533 [email protected]
Technical Specs
Product Dimension
Operation Interface Instruction
DMX-1CH-10A
Decode Channel
1CH
Input Signal
DMX-512/1990 digital signal
Output Signal
Constant Voltage PWM
Power Supply
DC 12~24V
Power Dis.
1CH×10A
Power Output
120W(12V)/240W(24V)
Operating Temp.
-30˚C~55˚C
Size
L7''×W1.8''×H1.2''in
(L176xW46xH30mm)
Weight
6oz
(170g)
6.4in (162mm)
7in (176mm)
0.3in
(7mm)
0.3in
(7mm)
1.8in (46mm)
0.9in (22mm)
1.2in (30mm)
M
-
+
+
-
GND
DMX+
DMX -
GND
DMX+
LED DMX & P
WM
DIMMER - MONO
DMX -
OUTPUT LED
max. 1x10A
POWER IN
12-24VDC
M
-
+
+
-
GND
DMX+
DMX -
GND
DMX+
LED DMX & P
WM
DIMMER - MONO
DMX -
OUTPUT LED
max. 1x10A
POWER IN
12-24VDC
POWER SUPPLY
M
-
+
+
-
GND
DMX+
DMX -
GND
DMX+
LED DMX & P
WM
DIMMER - MONO
DMX -
OUTPUT LED
max. 1x10A
POWER IN
12-24VDC
POWER SUPPLY
M
-
+
+
-
GND
DMX+
DMX -
GND
DMX+
LED DMX & P
WM
DIMMER - MONO
DMX -
OUTPUT LED
max. 1x10A
POWER IN
12-24VDC
POWER SUPPLY
6.4in (162mm)
7in (176mm)
0.3in
(7mm)
0.3in
(7mm)
1.8in (46mm)
0.9in (22mm)
1.2in (30mm)
M
-
+
+
-
GND
DMX+
DMX -
GND
DMX+
LED DMX & P
WM
DIMMER - MONO
DMX -
OUTPUT LED
max. 1x10A
POWER IN
12-24VDC
M
-
+
+
-
GND
DMX+
DMX -
GND
DMX+
LED DMX & P
WM
DIMMER - MONO
DMX -
OUTPUT LED
max. 1x10A
POWER IN
12-24VDC
POWER SUPPLY
M
-
+
+
-
GND
DMX+
DMX -
GND
DMX+
LED DMX & P
WM
DIMMER - MONO
DMX -
OUTPUT LED
max. 1x10A
POWER IN
12-24VDC
POWER SUPPLY
M
-
+
+
-
GND
DMX+
DMX -
GND
DMX+
LED DMX & P
WM
DIMMER - MONO
DMX -
OUTPUT LED
max. 1x10A
POWER IN
12-24VDC
POWER SUPPLY
DMX +
DMX Data High
DMX -
DMX Data Low
GND
DMX Ground
DMX Input Signal
(DMX 512)
DMX +
DMX Data High
DMX -
DMX Data Low
GND
DMX Ground
DMX Output Signal
V-
DC Power In Negative
V+
DC Power In Positive
DC 12-24V
(12 volt - 24 volt DC)
V-
DC Power Output Negative
V+
DC Power Output Positive
Output Channels
(1x10 Amp - 10 Amp Total)
Display
Current Starting DMX Channel
Button M
Changes Digit Selection
Increase Selection
Button -
Decrease Selection
Display and Buttons
Wiring
Programming
Setting the base channel:
Press any button to wake up the display if no numbers are displayed. Press and
hold M button for 3 seconds until hundreds digit flashes. Use + and - buttons to select hundreds
digit. Press M button until tens digit flashes. Use + and - buttons to select tens digit. Press M button until ones flashes. Use + and - buttons to select ones digit. When the desired
base channel is displayed, do not press any buttons. In approximately 15 seconds, all of the digits in the display will stop flashing and the base channel is set.