background image

©SUPERA

V.1.0    |    August 2014

INS

TRUCTION 

MANU

AL

WARNINGS

•  Do not touch any hot surfaces
•  Do not immerse unit, cord or plug in liquid at any time
•  Unplug cord from outlet when not in use and before cleaning
•  Plug only into a 3-hole grounded electrical outlet
•  Do not operate unattended
•  Do not use this unit for anything other than intended use
•  Do not use outdoors
•  Always use on a fi rm, dry and level surface at least 12” from walls or any other obstruction
•  Do not use if unit has a damaged cord or plug, in the event the appliance malfunctions, or has 

been damaged in any manner

•  Keep children and animals away from unit
•  Any incorrect installation, alterations, adjustments and/or improper maintenance can lead to 

property loss and injury.  All repairs should be done by authorized professionals only

•  Ensure that the designated power supply is adequate for continual usage and the voltage is 

correct

INSTALLATION

1.  Remove the unit and all packing materials from the carton and remove protective covering from 

the unit and parts.

2.  Remove tape from the discharge chute, crumb tray and toast collector pan.
3.  If the unit is not level, use the feet to level.
4.  The toast feed ramp is installed at the factory and can be used in two positions:
 

-

When in the upright position, the toaster is set for automatic feed.  Bread products enter  

 

   

  the toaster by placing them on the feed ramp and releasing.

 

-For manual feeding of product, tip the feed ramp until it rests on top of the unit. In this position  

   

  bread products can be manually loaded by placing them directly on the conveyor belt.

5.  Install toast crumb tray directly below the conveyor belt and below the stop pins. Insert until 

the front of the crumb tray meets the stop pins.

TO USE

1.  Plug toaster into a properly grounded electrical outlet. 
2.  Rotate the Rotary switch in the high-heat position.
3.  Turn the Color Control to the lightest position while the unit heats up. (Note: Allow                 

approximately 15 to 20 minutes for a warm-up period.)

4.  After warm-up period, set the Color Control to the medium position and toast two slices of 

bread product then re-adjust the Color Control to the desired setting. (Note: To toast moist 
products such as English Muffi

  ns, rye bread or whole wheat, slow the conveyor by turning the 

Color Control knob to a darker setting clockwise).

5.  This unit can be used for one sided toasting, such as buns and English Muffi

  ns by rotating the 

rotary switch to the top side heat only.

6.  Never use the toaster when the crumb tray is not in place.

POWER SAVE MODE

To go into a Power Save Mode, turn the rotary selector to Power Save Mode. The toaster is          
operating at 25% power.  (Note: To place toaster back into full operation turn the selector back into 
TOAST. Unit is back up to full power within 5 minutes.)

Summary of Contents for CYT-120-1







Reviews: