background image

PROTECT YOUR HANDS

Keep you hands away from splits and cracks which open in the log; They may close suddenly and crush or ampu-

tate your hands.

Do not remove jammed logs with you hands.

DON'T FORCE TOOL

It will do a better and safer job at its design rate. Never try to split logs larger than those indicated in the specifica-

tions table. This could be dangerous and may damage the machine.

Don’t use log splitter for a purpose for which it was not intended.

NEVER LEAVE TOOL RUNNING UNATTENDED

Don’t leave tool until i t has come to a complete stop.

DISCONNECT POWER

Don’t leave tool until i t has come to a complete stop.

PROTECT THE ENVIRONMENT GB

Take used oil to an authorized collection point or follow the stipulations in the country where the log splitter is used.

Do not discharge into drains, soil or water.

MAINTAIN YOUR LOG SPLITTER WITH CARE

Keep the log splitter clean for best and safest performance.

MAKE THE WORKSHOP CHILDPROOF

Lock the shop. Disconnect master switches.

Store the log splitter away from children and others not qualified to use it.

APPLICATION CONDITIONS

This log splitter is a home use model. It is designed for operating under ambient temperatures between 41°Fand 

104°F (+5°C and 40°C and for installation at altitudes no more than 3280FT.(1000m) above M.S.L. The

surrounding humidity should less than 50% at 104°F (40°C). It can be stored or transported under ambient 

temperatures between -13°F and 131°F (-25°C and 55°C).

ELECTRICAL REQUIREMENTS

Connect the main leads to a standard 110V+10% (60Hz+1Hz) electrical supply which has protection devices of 

under-voltage, overvoltage, over-current as well as a residual current device (RCD) which maximum residual

current rated at 0.03A.

CONTENTS SUPPLIED

The log splitter comes partially assembled and is shipped in 

carefully packed carton. After all the parts have been 

removed from the carton, you should have:

1. Log splitter Frame

2. Wheel (1 pair)

3. Operator’s Manual & Engine 

Manual

4. Hardware Bag, Including

4

3

4

2

1

X 2

X 2

C

Summary of Contents for GUT065













Reviews: